Products

Industries

Blog

Contact

Book a demo

Equipment

Rigol

Rigol RSA3015E-TG

SCPI COMMAND REFERENCE

Rigol RSA3015E-TG

The Rigol RSA3015E-TG is Rigol's spectrum analyzer in the RSA3000E Series Real-time Spectrum Analyzer family. Its SCPI remote-control interface exposes 505 commands across 24 subsystems - 434 settable and 71 queries - and every command is documented here with its parameters, accepted values, return format, and a copy-paste PyVISA example for automating test and measurement.

505

Commands

434

Settable

Queries

Subsystems

SCPI

Verified

2026-07-16

All commands

:CALCulate:BANDwidth|BWIDth:NDBset / query

Sets the N value in N dB BW measurement and queries the current N value. The command is invalid for the PvT measurement mode in RTSA.

Name	Type	Values	Description
<rel_ampl>	real	-140 dB - -0.01 dB	Consecutive real number used as the relative amplitude for the N dB bandwidth measurement.

real - The query returns the N value in scientific notation.

:CALCulate:BANDwidth:NDB -4
:CALCulate:BWIDth:NDB -4
:CALCulate:BANDwidth:NDB?
:CALCulate:BWIDth:NDB?

:CALCulate:BANDwidth|BWIDth:RESult?query

Queries the measurement results of the N dB band. The returned bandwidth value is in Hz and is reported in scientific notation; if the two points at both sides of the current marker are not found, the query returns -1.000000000e+02.

real (Hz) - Bandwidth value of the N dB band in scientific notation. If the two points at both sides of the current marker with N dB fall or rise in peak amplitude are not found, returns -1.000000000e+02.

:CALCulate:BANDwidth|BWIDth:RESult?

:CALCulate:BANDwidth|BWIDth:RLEFt?query

Queries the frequency value of the frequency point located to the left of the current marker at the N dB fall or rise in peak amplitude. Invalid for PvT measurement mode in RTSA.

real (Hz) - Returns the frequency value in scientific notation, in Hz. If the frequency point is not found, returns -1.000000000e+02.

:CALCulate:BANDwidth|BWIDth:RRIGht?query

Queries the frequency value of the frequency point that is located at the right side of the current marker with N dB fall or rise in its peak amplitude. If the frequency point is not found, the query returns -1.000000000e+02.

real (Hz) - The frequency value in scientific notation, in Hz. If the point is not found, the query returns -1.000000000e+02.

:CALCulate:LLINe:ALL:DELeteset / query

Deletes all the limit line data.

:CALCulate:LLINe:TESTset / query

Enables or disables the limit line test function. The query returns the setting state as 0 or 1.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the limit line test function.

integer - The query returns 0 or 1.

:CALCulate:LLINe:TEST OFF or :CALCulate:LLINe:TEST 0
:CALCulate:LLINe:TEST?

:CALCulate:LLINe<n>:AMPLitude:CMODe:RELativeset / query

Enables or disables the coupling between the selected limit line data points and the reference level. The query returns the setting state as 0 or 1.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the coupling function.

enum - Returns the setting state of the coupling function as 0 or 1.

:CALCulate:LLINe<n>:AMPLitude:CMODe:RELative OFF|ON|0|1
:CALCulate:LLINe<n>:AMPLitude:CMODe:RELative?

:CALCulate:LLINe<n>:BUILdset / query

Builds the selected limit line from the specified trace.

Name	Type	Values	Description
nopt	integer	1 - 6	Selects the limit line number.
trace	enum	TRACE1 \| TRACE2 \| TRACE3	Selects the trace used to build the limit line.

:CALCulate:LLINe2:BUILd TRACE2

:CALCulate:LLINe<n>:COPYset / query

Copies the selected limit line to the current limit line.

Name	Type	Values	Description
n	integer	1 - 6	Limit line number to copy to.
source	enum	LLINE1 \| LLINE2 \| LLINE3 \| LLINE4 \| LLINE5 \| LLINE6	Limit line to copy from.

:CALCulate:LLINe2:COPY LLINE1

:CALCulate:LLINe<n>:DATAset / query

Edits one limit line and marks it with n. The query returns the limit line data currently being edited.

Name	Type	Values	Description
n	integer	1 - 6	Limit line number to edit.
x	real	0 Hz - 3 GHz	Frequency value for a data point.
ampl	real	-1,000 dBm - 1,000 dBm	Amplitude value for a data point.
connect	integer	0 - 1	Connection flag for the data point.

string - The query returns the limit line data currently being edited.

:CALCulate:LLINe1:CONTrol:INTerpolate:TYPE LINear
:CALCulate:LLINe1:CONTrol:INTerpolate:TYPE?

:CALCulate:LLINe<n>:DELeteset / query

Deletes the selected limit line.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6	Selects the limit line to delete.

::CALCulate:LLINe2:DELete

:CALCulate:LLINe<n>:DISPlayset / query

Turns on or off the selected limit line. Queries the setting state of the selected limit line.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6	Selects the limit line number.
state	enum	OFF \| ON \| 0 \| 1	Turns the selected limit line off or on.

integer - Returns 0 or 1 indicating the setting state of the selected limit line.

:CALCulate:LLINe2:DISPlay OFF|ON|0|1
:CALCulate:LLINe2:DISPlay?

:CALCulate:LLINe<n>:FAIL?query

Queries the measurement results of the selected limit line and its associated trace.

Name	Type	Values	Description
n	discrete	1 - 6

enum - Returns 0 for pass or 1 for fail.

:CALCulate:LLINe<n>:FREQuency:CMODe:RELativeset / query

Enables or disables the coupling function between the selected limit line data points and the center frequency. The query returns the current coupling state.

Name	Type	Values	Description
n	integer	1 - 6	Selects the limit line number.
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the coupling function.

enum - Returns the current coupling setting: OFF/0 for disabled or ON/1 for enabled.

:CALCulate:LLINe<n>:MARGinset / query

Sets the margin for the selected limit line. Queries the margin for the selected limit line.

Name	Type	Values	Description
n	discrete	1 - 6	Selects the limit line number.
rel_ampl	real	-40 dB - 0 dB	Sets the margin value for the selected limit line.

real - The query returns the margin for the limit line in scientific notation.

:CALCulate:LLINe2:MARGin 1
:CALCulate:LLINe2:MARGin?

:CALCulate:LLINe<n>:MARGin:STATeset / query

Enables or disables the margin for the selected limit line. Queries the setting state of the margin for the selected limit line.

Name	Type	Values	Description
<n>	integer	1 - 6	Selects the limit line number.
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the margin.

enum - Returns the margin state as 0 or 1.

:CALCulate:LLINe<n>:TRACeset / query

Sets the trace for the current limit line test. Queries the trace for the current limit line test.

Name	Type	Values	Description
n	integer	1 - 6	Limit line number.
trace	integer	1 - 3	Trace number used for the current limit line test.

integer - Returns the trace number for the current limit line test.

:CALCulate:LLINe3:TRACe 2
:CALCulate:LLINe3:TRACe?

:CALCulate:LLINe<n>:TYPEset / query

Sets the type of the specified limit line. Queries the type of the specified limit line.

Name	Type	Values	Description
<n>	integer	1 - 6
type	enum	UPPer \| LOWer	Selects whether the limit line is upper or lower type.

enum - The query returns UPP or LOW.

:CALCulate:MARKer:AOFFset / query

Turns off all the enabled markers.

:CALCulate:MARKer:COUPle[:STATe]set / query

Enables or disables the couple marker function. When enabled, moving any marker makes other non-fixed, non-off markers move along with it.

Name	Type	Values	Description
stateopt	enum	OFF \| ON \| 0 \| 1	Couple marker function state.

:CALCulate:MARKer:COUPle:STATe OFF or :CALCulate:MARKer:COUPle:STATe 0
:CALCulate:MARKer:COUPle:STATe?

:CALCulate:MARKer:PEAK:EXCursionset / query

Sets the peak offset in dB. Queries the peak offset.

Name	Type	Values	Description
rel_ampl	real	dB	Peak offset value.

:CALCulate:MARKer:PEAK:EXCursion:STATeset / query

Enables or disables the peak offset function. Queries the status of the peak offset function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the peak offset function.

enum - The query returns 0 or 1.

:CALCulate:MARKer:PEAK:EXCursion:STATe ON or :CALCulate:MARKer:PEAK:EXCursion:STATe 1
:CALCulate:MARKer:PEAK:EXCursion:STATe?

:CALCulate:MARKer:PEAK:SEARch:MODEset / query

Sets the peak search mode. Queries the peak search mode.

Name	Type	Values	Description
mode	enum	PARameter \| MAXimum	Peak search mode.

:CALCulate:MARKer:PEAK:SORTset / query

Sets or queries the sorting order of the data displayed in the peak table.

Name	Type	Values	Description
mode	enum	FREQuency \| AMPLitude	Sort order for the peak table data.

enum - Returns the current peak table sorting order.

:CALCulate:MARKer:PEAK:SORT AMPLitude
:CALCulate:MARKer:PEAK:SORT?

:CALCulate:MARKer:PEAK:TABLe:READoutset / query

Queries or sets the peak-table readout mode used to list peaks meeting the peak criteria. The available modes are ALL, GTDLine, and LTDLine.

Name	Type	Values	Description
mode	enum	ALL \| GTDLine \| LTDLine	Selects which peaks are listed in the peak table readout.

enum - Returns the current readout mode as ALL (NORM), GTDL (DLM), or LTDL (DLL).

:CALCulate:MARKer:PEAK:TABLe:READout GTDLine
:CALCulate:MARKer:PEAK:TABLe:READout?

:CALCulate:MARKer:PEAK:TABLe[:STATe]set / query

Enables or disables the peak table. Queries the status of the peak table.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the peak table off or on.

enum - Returns the peak table status.

:CALCulate:MARKer:PEAK:TABLe:STATe OFF|ON|0|1
:CALCulate:MARKer:PEAK:TABLe:STATe?

:CALCulate:MARKer:PEAK:THResholdset / query

Sets the peak threshold, with a default unit of dBm. Queries the peak threshold.

Name	Type	Values	Description
ampl	real	-200 dBm - 0 dBm	Peak threshold amplitude.

real - The query returns the peak threshold in scientific notation.

:CALCulate:MARKer:PEAK:THReshold -100
:CALCulate:MARKer:PEAK:THReshold?

:CALCulate:MARKer:PEAK:THReshold:STATeset / query

Enables or disables the peak threshold function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the peak threshold function.

:CALCulate:MARKer:TABLe[:STATe]set / query

Enables or disables the marker table. Queries the status of the marker table.

Name	Type	Values	Description
stateopt	enum	OFF \| ON \| 0 \| 1	Enables or disables the marker table.

enum - The query returns 0 or 1.

:CALCulate:MARKer:TRCKing[:STATe]set / query

Enables or disables the signal track. Queries the status of the signal track.

Name	Type	Values	Description
stateopt	boolean	OFF \| ON \| 0 \| 1	Boolean state to enable or disable signal track.

integer - The query returns 0 or 1.

:CALCulate:MARKer:TRCKing:STATe OFF or :CALCulate:MARKer:TRCKing:STATe 0
:CALCulate:MARKer:TRCKing:STATe?

:CALCulate:MARKer<n>:CPSearch[:STATe]set / query

Enables or disables continuous peak search function, and marks the peak value with n. Queries the status of the continuous peak search function.

Name	Type	Values	Description
<n>	discrete	1 - 8	Marker number.
state	enum	OFF \| ON \| 0 \| 1	Turns continuous peak search on or off.

enum - Returns the status of continuous peak search.

:CALCulate:MARKer1:CPSeatch:STATe ON or :CALCulate:MARKer1:CPSeatch:STATe 1
:CALCulate:MARKer1:CPSeatch:STATe?

:CALCulate:MARKer<n>:FCOunt:GATetimeset / query

Sets the gate time for Marker n. The unit is s. Queries the gate time for Marker n.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.
time	real	1 μs - 500 ms	Gate time for Marker n.

real - The query returns the gate time for Marker n in scientific notation.

:CALCulate:MARKer2:FCOunt:GATetime 0.01
:CALCulate:MARKer2:FCOunt:GATetime?

:CALCulate:MARKer<n>:FCOunt:GATetime:AUTOset / query

Turns on or off the auto gate time for Marker n. Queries the status of the auto gate time for Marker n.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8
state	boolean	OFF \| ON \| 0 \| 1	Enables or disables auto gate time.

boolean - Returns 1 if auto gate time is enabled and 0 if it is disabled.

:CALCulate:MARKer2:FCOunt:GATetime:AUTO ON or :CALCulate:MARKer2:FCOunt:GATetime:AUTO 1
:CALCulate:MARKer2:FCOunt:GATetime:AUTO?

:CALCulate:MARKer<n>:FCOunt[:STATe]set / query

Enables or disables the frequency counter function of the specified marker. The query returns the status of that function as 0 or 1.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.
state	enum	OFF \| ON \| 0 \| 1	Turns the frequency counter function off or on.

enum - Returns the frequency counter status as 0 or 1.

:CALCulate:MARKer2:FCOunt:STATe ON or :CALCulate:MARKer2:FCOunt:STATe 1
:CALCulate:MARKer2:FCOunt:STATe?

:CALCulate:MARKer<n>:FCOunt:X?query

Queries the readout of the frequency counter of the specified marker. The readout is returned as an integer in Hz; when the frequency counter function is disabled, the command returns NAN.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.

integer (Hz) - Readout of the frequency counter of the specified marker, returned in Hz.

:CALCulate:MARKer2:FCOunt:X?

:CALCulate:MARKer<n>:FUNCtionset / query

Selects the special measurement type for the specified marker. Queries the special measurement type of the specified marker.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.
mode	enum	NOISe \| BPOWer \| BDENsity \| OFF	Special measurement type for the specified marker.

enum - The query returns NOIS, BPOW, BDEN, or OFF.

:CALCulate:MARKer1:FUNCtion NOISe
:CALCulate:MARKer1:FUNCtion?

:CALCulate:MARKer<n>:FUNCtion:BAND:LEFTset / query

Sets or queries the left edge frequency or time of the signal used in the band function calculation for the specified marker. It is only valid when the corresponding bandwidth function is enabled.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number.
freq	real	0 - band right	Left edge frequency or time of the signal involved in the band function calculation.

real - Returns the left edge frequency or time of the signal in scientific notation.

:CALCulate:MARKer1:FUNCtion:BAND:LEFT <freq>
:CALCulate:MARKer1:FUNCtion:BAND:LEFT?

:CALCulate:MARKer<n>:FUNCtion:BAND:RIGHtset / query

Sets or queries the right edge frequency or time of the signal involved in the calculation for the band function. It is only valid when the corresponding bandwidth function is enabled, and is used to set the right edge time in zero span or PvT view.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number.
freq	real	band left - +∞	Right edge frequency or time of the signal involved in the calculation.

real - Returns the right edge frequency or time of the signal in scientific notation.

:CALCulate:MARKer1:FUNCtion:BAND:RIGHt 4000000000
:CALCulate:MARKer1:FUNCtion:BAND:RIGHt?

:CALCulate:MARKer<n>:FUNCtion:BAND:SPANset / query

Sets the bandwidth or the time span of the signal involved in the calculation for the band function. Queries the bandwidth or the time span of the signal involved in the calculation for the band function.

Name	Type	Values	Description
n	discrete	1 - 8
freq	real	0 - +∞	Consecutive real number specifying the bandwidth or time span used in the band function calculation.

:CALCulate:MARKer1:FUNCtion:BAND:SPAN 500000000
:CALCulate:MARKer1:FUNCtion:BAND:SPAN?

:CALCulate:MARKer<n>:FUNCtion:BAND:SPAN:AUTOset / query

Enables or disables the band span auto function. The query returns the status of band span auto function.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.
state	enum	OFF \| ON \| 0 \| 1	Turns band span auto off or on.

enum - Returns the status of band span auto function.

:CALCulate:MARKer<n>:LINes[:STATe]set / query

Enables or disables the marker line of the specified marker. Queries the status for the marker line of the specified marker.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the marker line.

enum - Returns 0 or 1.

:CALCulate:MARKer1:LINes:STATe ON or :CALCulate:MARKer1:LINes:STATe 1
:CALCulate:MARKer1:LINes:STATe?

:CALCulate:MARKer<n>:MAXimum:LEFTset / query

Searches for and marks the nearest peak located to the left of the current peak that meets the peak search condition.

:CALCulate:MARKer<n>:MAXimum[:MAX]set / query

Performs one peak search based on the search mode set by :CALCulate:MARKer:PEAK:SEARch:MODE and marks it with the specified marker. When no peak is found, the instrument displays "No peak found".

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number to use for the peak search.

:CALCulate:MARKer2:MAXimum:MAX

:CALCulate:MARKer<n>:MAXimum:NEXTset / query

Searches for and marks the peak whose amplitude on the trace is next to that of the current peak and which meets the peak search condition.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number to use.

:CALCulate:MARKer2:MAXimum:NEXT

:CALCulate:MARKer<n>:MAXimum:RIGHtset / query

Searches for and marks the nearest peak located on the right side of the current peak that meets the peak search condition.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number to use.

:CALCulate:MARKer2:MAXimum:RIGHt

:CALCulate:MARKer<n>:MINimumset / query

Searches for and marks the peak with the minimum amplitude on the trace.

Name	Type	Values	Description
n	integer	1 - 8

:CALCulate:MARKer2:MINimum

:CALCulate:MARKer<n>:MODEset / query

Sets the type of the specified marker. The query returns the current marker type.

Name	Type	Values	Description
n	integer	1 - 8	Specifies the marker number.
mode	enum	POSition \| DELTa \| FIXed \| OFF	Selects the marker mode.

enum - Returns the type of the specified marker as POS, DELT, FIX, or OFF.

:CALCulate:MARKer1:MODE POSition
:CALCulate:MARKer1:MODE?

:CALCulate:MARKer<n>:PTPeakset / query

Performs the peak-peak search and marks it with the specified marker. After execution, the marker mode of the specified marker is set to Delta automatically.

Name	Type	Values	Description
n	integer	1 - 8	Marker number.

:CALCulate:MARKer1:PTPeak

:CALCulate:MARKer<n>:REFerenceset / query

Sets the reference marker for the specified marker. Queries the reference marker for the specified marker.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Specifies the marker number.
integer	integer	1 - 8	Specifies the reference marker number.

integer - Returns the reference marker number for the specified marker.

:CALCulate:MARKer1:REFerence 2
:CALCulate:MARKer1:REFerence?

:CALCulate:MARKer<n>[:SET]:CENTerset / query

Sets the center frequency of the analyzer to the frequency of the specified marker.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Specifies which marker to use.

:CALCulate:MARKer1:SET:CENTer

:CALCulate:MARKer<n>[:SET]:DELTa:CENTerset / query

Sets the center frequency of the analyzer to half of the frequency difference (absolute frequency) between the two Delta markers. It is only valid when the current marker mode is "Delta".

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number.

:CALCulate:MARKer1:SET:DELTa:CENTer

:CALCulate:MARKer<n>[:SET]:DELTa:SPANset / query

Sets the frequency difference of the specified Delta marker to the span of the analyzer.

Name	Type	Values	Description
n	integer	1 - 8	Specifies the marker number.

:CALCulate:MARKer1:SET:DELTa:SPAN

:CALCulate:MARKer<n>[:SET]:RLEVelset / query

Sets the reference level of the analyzer to the amplitude of the specified marker.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number to use.

:CALCulate:MARKer<n>[:SET]:STARtset / query

Sets the start frequency of the analyzer to the frequency of the specified marker. If the marker is in Delta mode, the start frequency is set to the Delta marker frequency.

Name	Type	Values	Description
n	discrete	1 - 8	Specifies which marker is used.

:CALCulate:MARKer3:SET:STARt

:CALCulate:MARKer<n>[:SET]:STEPset / query

Sets the center frequency step of the analyzer to the frequency of the specified marker. If the marker mode of the specified marker is Position or Fixed, the center frequency step is set to the frequency of the marker.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.

:CALCulate:MARKer3:SET:STEP

:CALCulate:MARKer<n>[:SET]:STOPset / query

Sets the stop frequency of the analyzer to the frequency of the specified marker. If the marker mode is Position or Fixed, the stop frequency is set to the marker frequency; if the marker mode is Delta, it is set to the Delta marker frequency.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Specifies the marker number.

:CALCulate:MARKer2:SET:STOP

:CALCulate:MARKer<n>:STATeset / query

Enables or disables the specified marker. Queries the status of the specified marker.

Name	Type	Values	Description
<n>	integer	1 - 8	Marker number to select.
state	enum	OFF \| ON \| 0 \| 1	Sets the marker state.

enum - Returns 0 or 1 for the marker status.

:CALCulate:MARKer1:STATe ON
:CALCulate:MARKer1:STATe 1
:CALCulate:MARKer1:STATe?

:CALCulate:MARKer<n>:TRACeset / query

Sets the marker trace for the specified marker. Queries the marker trace for the specified marker.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.
integer	integer	1 - 6	Marker trace number to select.

discrete - Returns the marker trace for the specified marker.

:CALCulate:MARKer1:TRACe 1
:CALCulate:MARKer1:TRACe?

:CALCulate:MARKer<n>:TRACe:AUTOset / query

Enables or disables the auto trace marking of the specified marker. Queries the status of the auto trace marking of the specified marker.

Name	Type	Values	Description
<n>	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8
state	boolean	OFF \| ON \| 0 \| 1	Turns auto trace marking off or on for the specified marker.

enum - Returns the auto trace marking status as 0 or 1.

:CALCulate:MARKer1:TRACe:AUTO ON or :CALCulate:MARKer1:TRACe:AUTO 1
:CALCulate:MARKer1:TRACe:AUTO?

:CALCulate:MARKer<n>:Xset / query

Sets the frequency of the specified marker. Queries the frequency of the specified marker.

Name	Type	Values	Description
n	discrete	1 - 8	Specifies which marker to access.
param	real	30 MHz - 1 GHz	Sets the marker frequency.

string - The query returns the frequency of the specified marker in scientific notation.

:CALCulate:MARKer1:X 515000000
:CALCulate:MARKer1:X?

:CALCulate:MARKer<n>:X:READoutset / query

Sets the readout mode of the X axis of the specified marker. The readout mode can be Frequency, Time, ITime, or Period.

Name	Type	Values	Description
n	discrete	1 - 8
mode	enum	FREQuency \| TIME \| ITIMe \| PERiod	Selects the X-axis readout mode for the specified marker.

:CALCulate:MARKer<n>:X:READout:AUTOset / query

Enables or disables the auto readout mode of the specified marker. When enabled, if the marker trace changes, the readout mode is re-determined based on the destination trace.

Name	Type	Values	Description
<n>	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number.
state	boolean	OFF \| ON \| 0 \| 1	Turns auto readout mode off or on.

:CALCulate:MARKer1:X:READout:AUTO ON or :CALCulate:MARKer1:X:READout:AUTO 1
:CALCulate:MARKer1:X:READout:AUTO?

:CALCulate:MARKer<n>:Yset / query

Sets the Y-axis value of the specified fixed marker. Queries the Y-axis value of the specified marker, with a default unit of dBm.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Specifies the marker number.
amp	real	-170 dBm - 30 dBm	Sets the marker Y-axis value.

real - Returns the Y-axis value in scientific notation.

:CALCulate:MARKer1:Y -59.6
:CALCulate:MARKer1:Y?

:CALCulate:MARKer<n>:Z:POSitionset / query

Sets the trace number of the trace where the marker stays in the Spectrogram view. Queries the trace number of the trace where the marker stays in the Spectrogram view.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number.
integer	integer	1 - 8192	Trace number of the trace where the marker stays in the Spectrogram view.

integer - The query returns the trace number in integer.

:CALCulate:MARKer1:Z:POSition 1
:CALCulate:MARKer1:Z:POSition?

:CALCulate:MATHset / query

Sets mathematical operations between traces and, in some cases, user-defined offsets. Queries the math operation function of the specified trace.

Name	Type	Values
trace_destination	enum	TRACE1 \| TRACE2 \| TRACE3 \| TRACE4 \| TRACE5 \| TRACE6
function_math	enum	PDIFference \| PSUM \| LOFFset \| LMOFFset \| LDIFference \| OFF
trace1_operation	enum	TRACE1 \| TRACE2 \| TRACE3 \| TRACE4 \| TRACE5 \| TRACE6
trace2_operation	enum	TRACE1 \| TRACE2 \| TRACE3 \| TRACE4 \| TRACE5 \| TRACE6
rel_offset	real	-100 dB - 100 dB
rel_reference	real	-170 dBm - 30 dBm

enum - Returns the operation function of the specified trace.

:CALCulate:NTData[:STATe]set / query

Enables or disables the normalize function. The query reports the current normalization status.

Name	Type	Values	Description
state	boolean	-	Turns normalization off or on.

integer - Returns the normalization status as 0 or 1.

:CALCulate:NTData:STATe ON or :CALCulate:NTData:STATe 1
:CALCulate:NTData:STATe?

:CALCulate:EMI:SLISt:DELeteset / query

Deletes signals from the EMI signal table according to the selected scope. The scope can be all, current, marked, or unmarked signals.

Name	Type	Values	Description
scope	enum	ALL \| CURRent \| MARKed \| UNMarked	Selects which signals to delete from the signal table.

:CALCulate:EMI:SLISt:DELete ALL

:CALCulate:FSCan:MAMarker[:SET]:SLIStset / query

Adds the current measurement results to the signal table.

:CALCulate:FSCan:MARKer:AOFFset / query

Turns off all the enabled markers.

:CALCulate:FSCan:MARKer:AOFF

:CALCulate:FSCan:MARKer:COUPle[:STATe]set / query

Enables or disables the couple marker function. The query returns the state of the couple marker function.

Name	Type	Values	Description
stateopt	enum	OFF \| ON \| 0 \| 1	Sets the couple marker function state.

enum - State of the couple marker function.

:CALCulate:FSCan:MARKer:COUPle[:STATe] OFF|ON|0|1
:CALCulate:FSCan:MARKer:COUPle[:STATe]?

:CALCulate:FSCan:MARKer:PEAK:EXCursionset / query

Sets the peak excursion. The unit is dB. Queries the peak excursion.

Name	Type	Values	Description
rel_ampl	real	0 dB - 100 dB	Consecutive real number specifying the peak excursion.

real (dB) - The query returns the peak excursion in scientific notation.

:CALCulate:FSCan:MARKer:PEAK:EXCursion 12
:CALCulate:FSCan:MARKer:PEAK:EXCursion?

:CALCulate:FSCan:MARKer:PEAK:EXCursion:STATeset / query

Enables or disables the peak excursion function. Queries the status of the peak excursion function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the peak excursion function off or on.

enum - Returns the status of the peak excursion function as 0 or 1.

:CALCulate:FSCan:MARKer:PEAK:SEARch:MODEset / query

Sets the peak search mode and queries the current peak search mode. The command is only valid for peak search executed by the :CALCulate:FSCan:MARKer<n>:MAXimum command.

Name	Type	Values	Description
mode	enum	PARameter \| MAXimum	Peak search mode selection.

enum - Returns the current peak search mode.

:CALCulate:FSCan:MARKer:PEAK:SEARch:MODE PARameter
:CALCulate:FSCan:MARKer:PEAK:SEARch:MODE?

:CALCulate:FSCan:MARKer:PEAK:SEARch:THResholdset / query

Sets the peak threshold and queries the peak threshold.

Name	Type	Values	Description
ampl	real	-200 dBm - 0 dBm	Peak threshold amplitude.

real - The query returns the peak threshold in scientific notation.

:CALCulate:FSCan:MARKer:PEAK:SEARch:THReshold -100
:CALCulate:FSCan:MARKer:PEAK:SEARch:THReshold?

:CALCulate:FSCan:MARKer:PEAK:SEARch:THReshold:STATeset / query

Enables or disables the peak threshold function. Queries the status of the peak threshold function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the peak threshold function.

:CALCulate:FSCan:MARker<n>:FUNCtion:MAMarker?query

Queries the result measured at the marker. The query returns the detector 1, detector 2, detector 3, and frequency values at the marker in scientific notation, separated by commas; if the detector is disabled or the measurement is not completed, it returns -1.700000000e+02.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number to query.

string - Returns the result measured at the marker as four comma-separated scientific-notation values: detector 1 amplitude, detector 2 amplitude, detector 3 amplitude, and frequency. If the detector is disabled or the measurement is not completed, returns -1.700000000e+02.

:CALCulate:FSCan:MARker1:FUNCtion:MAMarker?

:CALCulate:FSCan:MARKer<n>:MAXimumset / query

Performs one peak search based on the search mode set by the :CALCulate:FSCan:MARKer:PEAK:SEARch:MODE command and marks it with the specified marker.

Name	Type	Values	Description
n	integer	1 - 8	Marker number.

:CALCulate:FSCan:MARKer2:MAXimum:MAX

:CALCulate:FSCan:MARKer<n>:MAXimum:LEFTset / query

Searches for and marks the nearest peak located to the left of the current peak that meets the peak search condition.

Name	Type	Values	Description
n	integer	1 - 8	Marker number.

:CALCulate:FSCan:MARKer<n>:MAXimum:NEXTset / query

Searches for and marks the peak whose amplitude on the trace is next to that of the current peak and which meets the peak search condition.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.

:CALCulate:FSCan:MARKer2:MAXimum:NEXT

:CALCulate:FSCan:MARKer<n>:MAXimum:RIGHtset / query

Searches for and marks the nearest peak located to the right of the current peak that meets the peak search condition.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.

:CALCulate:FSCan:MARKer2:MAXimum:RIGHt

:CALCulate:FSCan:MARKer<n>:MINimumset / query

Searches for and marks the peak with the minimum amplitude on the trace.

Name	Type	Values	Description
n	discrete	1 - 8	Specifies the marker number.

:CALCulate:FSCan:MARKer2:MINimum

:CALCulate:FSCan:MARKer<n>:MODEset / query

Sets the type of the specified marker. Queries the type of the specified marker.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8
mode	enum	POSition \| DELTa \| OFF	Selects the marker type: position, delta, or off.

enum - Returns the marker type as POS, DELT, or OFF.

:CALCulate:FSCan:MARKer1:MODE POSition
:CALCulate:FSCan:MARKer1:MODE?

:CALCulate:FSCan:MARKer<n>:REFerenceset / query

Sets the reference marker for the specified marker. The query returns the current reference marker number for that marker.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Specifies the marker number.
integer	integer	1 - 8	Reference marker number to assign.

integer - Returns the reference marker number for the specified marker.

:CALCulate:FSCan:MARKer1:REFerence 2
:CALCulate:FSCan:MARKer1:REFerence?

:CALCulate:FSCan:MARKer<n>[:SET]:SLIStset / query

Adds the frequency at the specified marker to the signal table.

Name	Type	Values	Description
n	integer	1 - 8	Marker number to use.

:CALCulate:FSCan:MARKer1:SET:SLISt

:CALCulate:FSCan:MARKer<n>[:SET]:METerset / query

Sets the frequency at the currently selected marker to the frequency of the meter.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number.

:CALCulate:FSCan:MARKer<n>:TO:METerset / query

Sets the frequency of the meter to the frequency at the currently selected marker.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number.

:CALCulate:FSCan:MARKer1:TO:METer

:CALCulate:FSCan:MARKer<n>:TRACeset / query

Sets or queries the trace assigned to the specified marker. The trace index is from 1 to 3.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number.
integer	discrete	1 \| 2 \| 3	Marker trace number.

integer - Returns the marker trace number.

:CALCulate:FSCan:MARKer1:TRACe 2
:CALCulate:FSCan:MARKer1:TRACe?

:CALCulate:FSCan:SLISt:APPend:METerset / query

Adds the frequency of the meter to the signal table.

:CALCulate:FSCan:SLISt:DELete:SIGNalset / query

Deletes the selected signal(s) from the signal table.

Name	Type	Values	Description
integer	integer	1 - 2,000

:CALCulate:FSCan:SLISt:DELete:SIGNal 20

:CALCulate:FSCan:SLISt:MARK:ALLset / query

Marks all the signals in the signal table.

:CALCulate:FSCan:SLISt:MARK:CLEar:ALLset / query

Clears all the marks in the signal table.

:CALCulate:FSCan:SLISt:MARK:CLEar:SIGNalset / query

Clears the mark of the specified signal.

Name	Type	Values	Description
integer	integer	1 - 2,000

:CALCulate:FSCan:SLISt:MARK:SIGNalset / query

Marks the specified signal.

Name	Type	Values	Description
integer	integer	1 - 2,000	Specifies the signal number to mark in the signal table.

The following command marks Signal 20 in the signal table. :CALCulate:FSCan:SLISt:MARK:SIGNal 20

:CALCulate:FSCan:SLISt:REPLace:METerset / query

Replaces the frequency of the currently selected signal with the currently set frequency of the meter.

Name	Type	Values	Description
integer	integer	1 - 2,000

:CALCulate:FSCan:SLISt:REPLace:METer 20

:CALCulate:FSCan:SLISt:SET:METerset / query

Sets the frequency of the meter to the frequency of the specified signal.

Name	Type	Values	Description
integer	integer	1 - 2,000

:CALCulate:FSCan:SLISt:SORT:AUTOset / query

Enables or disables the auto sort function. Queries the status of the auto sort function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns auto sort off or on.

enum - The query returns 0 or 1.

:CALCulate:FSCan:SLISt:SORT:AUTO OFF or :CALCulate:FSCan:SLISt:SORT:AUTO 0
:CALCulate:FSCan:SLISt:SORT:AUTO?

:CALCulate:FSCan:SLISt:SORT:DAMPlitudeset / query

Sets the detector amplitude sorting mode for the signal. Queries the detector amplitude sorting mode for the signal.

Name	Type	Values	Description
mode	enum	DET1 \| DET2 \| DET3	Detector amplitude sorting mode for the signal.

:CALCulate:FSCan:SLISt:SORT:DAMPlitude DET1

:CALCulate:FSCan:SLISt:SORT:DLDeltaset / query

Sets the detector limit delta amplitude mode for the signal. Queries the detector limit delta amplitude mode for the signal.

Name	Type	Values	Description
mode	enum	DET1 \| DET2 \| DET3	Detector limit delta amplitude mode.

:CALCulate:FSCan:SLISt:SORT:DLDelta DET1
:CALCulate:FSCan:SLISt:SORT:DLDelta?

:CALCulate:FSCan:SLISt:SORT:ORDerset / query

Sets the sort order of the signal. Queries the sort order of the signal.

enum - The query returns ASC or DESC.

:CALCulate:FSCan:SLISt:SORT:ORDer ASCending
:CALCulate:FSCan:SLISt:SORT:ORDer?

:CALCulate:FSCan:SLISt:SORT:TYPEset / query

Sets the sort mode of the signal. Queries the sort mode of the signal.

Name	Type	Values	Description
mode	enum	FREQuency \| DAMPlitude \| DLDelta	Sort mode of the signal.

enum - The query returns FREQ, DAMP, or DLD.

::CALCulate:FSCan:SLISt:SORT:TYPE FREQuency
::CALCulate:FSCan:SLISt:SORT:TYPE?

:CALCulate:FSCan:SLISt:ZOOMset / query

Takes the midspan frequency as the reference and zooms the coordinate display at the selected signal of the signal table to 10% of the current span.

Name	Type	Values	Description
integer	integer	1 - 2,000

:CALCulate:FSCan:SLISt:ZOOM 3

:CALCulate:FSCan:SLISt:ZOOM:OUTset / query

Returns the coordinate display of the current signal to its previous display set before the Signal Zoom.

:CALCulate:LLINe:ALL:DELeteset / query

Deletes all the limit line data.

:CALCulate:LLINe:TESTset / query

Enables or disables the limit line test function. The query returns the setting state as 0 or 1.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the limit line test function.

integer - The query returns 0 or 1.

:CALCulate:LLINe:TEST OFF or :CALCulate:LLINe:TEST 0
:CALCulate:LLINe:TEST?

:CALCulate:LLINe<n>:AMPLitude:CMODe:RELativeset / query

Enables or disables the coupling between the selected limit line data points and the reference level. The query returns the setting state as 0 or 1.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the coupling function.

enum - Returns the setting state of the coupling function as 0 or 1.

:CALCulate:LLINe<n>:AMPLitude:CMODe:RELative OFF|ON|0|1
:CALCulate:LLINe<n>:AMPLitude:CMODe:RELative?

:CALCulate:LLINe<n>:BUILdset / query

Builds the selected limit line from the specified trace.

Name	Type	Values	Description
nopt	integer	1 - 6	Selects the limit line number.
trace	enum	TRACE1 \| TRACE2 \| TRACE3	Selects the trace used to build the limit line.

:CALCulate:LLINe2:BUILd TRACE2

:CALCulate:LLINe<n>:CONTrol:INTerpolate:TYPEset / query

Sets the frequency interpolation mode of the selected limit line. The query returns the current frequency interpolation mode.

Name	Type	Values	Description
mode	enum	LOGarithmic \| LINear	Frequency interpolation mode for the selected limit line.

:CALCulate:LLINe<n>:COPYset / query

Copies the selected limit line to the current limit line.

Name	Type	Values	Description
n	integer	1 - 6	Limit line number to copy to.
source	enum	LLINE1 \| LLINE2 \| LLINE3 \| LLINE4 \| LLINE5 \| LLINE6	Limit line to copy from.

:CALCulate:LLINe2:COPY LLINE1

:CALCulate:LLINe<n>:DATAset / query

Edits one limit line and marks it with n. The query returns the limit line data currently being edited.

Name	Type	Values	Description
n	integer	1 - 6	Limit line number to edit.
x	real	0 Hz - 3 GHz	Frequency value for a data point.
ampl	real	-1,000 dBm - 1,000 dBm	Amplitude value for a data point.
connect	integer	0 - 1	Connection flag for the data point.

string - The query returns the limit line data currently being edited.

:CALCulate:LLINe1:CONTrol:INTerpolate:TYPE LINear
:CALCulate:LLINe1:CONTrol:INTerpolate:TYPE?

:CALCulate:LLINe<n>:DELeteset / query

Deletes the selected limit line.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6	Selects the limit line to delete.

::CALCulate:LLINe2:DELete

:CALCulate:LLINe<n>:DISPlayset / query

Turns on or off the selected limit line. Queries the setting state of the selected limit line.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6	Selects the limit line number.
state	enum	OFF \| ON \| 0 \| 1	Turns the selected limit line off or on.

integer - Returns 0 or 1 indicating the setting state of the selected limit line.

:CALCulate:LLINe2:DISPlay OFF|ON|0|1
:CALCulate:LLINe2:DISPlay?

:CALCulate:LLINe<n>:FAIL?query

Queries the measurement results of the selected limit line and its associated trace.

Name	Type	Values	Description
n	discrete	1 - 6

enum - Returns 0 for pass or 1 for fail.

:CALCulate:LLINe<n>:FREQuency:CMODe:RELativeset / query

Enables or disables the coupling function between the selected limit line data points and the center frequency. The query returns the current coupling state.

Name	Type	Values	Description
n	integer	1 - 6	Selects the limit line number.
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the coupling function.

enum - Returns the current coupling setting: OFF/0 for disabled or ON/1 for enabled.

:CALCulate:LLINe<n>:MARGinset / query

Sets the margin for the selected limit line. Queries the margin for the selected limit line.

Name	Type	Values	Description
n	discrete	1 - 6	Selects the limit line number.
rel_ampl	real	-40 dB - 0 dB	Sets the margin value for the selected limit line.

real - The query returns the margin for the limit line in scientific notation.

:CALCulate:LLINe2:MARGin 1
:CALCulate:LLINe2:MARGin?

:CALCulate:LLINe<n>:MARGin:STATeset / query

Enables or disables the margin for the selected limit line. Queries the setting state of the margin for the selected limit line.

Name	Type	Values	Description
<n>	integer	1 - 6	Selects the limit line number.
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the margin.

enum - Returns the margin state as 0 or 1.

:CALCulate:LLINe<n>:OFFSet:Xset / query

Sets the frequency offset of the specified limit line. Queries the frequency offset of the specified limit line.

Name	Type	Values	Description
n	discrete	1 - 6	Specifies the limit line number.
freq	real	-1 GHz - 1 GHz	Sets the frequency offset.

string - The query returns the frequency offset in scientific notation.

:CALCulate:LLINe2:OFFSet:X 5000
:CALCulate:LLINe2:OFFSet:X?

:CALCulate:LLINe<n>:OFFSet:Yset / query

Sets the amplitude offset of the specified limit line. Queries the amplitude offset of the specified limit line.

Name	Type	Values	Description
n	discrete	1 - 6	Limit line number to apply the offset to.
re_ampl	real	-50 - 50	Amplitude offset value for the specified limit line.

real - The query returns the amplitude offset in scientific notation.

:CALCulate:LLINe<n>:TRACeset / query

Sets the trace for the current limit line test. Queries the trace for the current limit line test.

Name	Type	Values	Description
n	integer	1 - 6	Limit line number.
trace	integer	1 - 3	Trace number used for the current limit line test.

integer - Returns the trace number for the current limit line test.

:CALCulate:LLINe3:TRACe 2
:CALCulate:LLINe3:TRACe?

:CALCulate:MARker:PEAK:SEARch:THReshold:LINeset / query

Enables or disables the peak threshold line. Queries the status of the peak threshold line.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the peak threshold line.

enum - Returns the status of the peak threshold line.

:CALCulate:MARKer<n>:LINes[:STATe]set / query

Enables or disables the marker line of the specified marker. Queries the status for the marker line of the specified marker.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the marker line.

enum - Returns 0 or 1.

:CALCulate:MARKer1:LINes:STATe ON or :CALCulate:MARKer1:LINes:STATe 1
:CALCulate:MARKer1:LINes:STATe?

:CALCulate:MARKer<n>:STATeset / query

Enables or disables the specified marker. Queries the status of the specified marker.

Name	Type	Values	Description
<n>	integer	1 - 8	Marker number to select.
state	enum	OFF \| ON \| 0 \| 1	Sets the marker state.

enum - Returns 0 or 1 for the marker status.

:CALCulate:MARKer1:STATe ON
:CALCulate:MARKer1:STATe 1
:CALCulate:MARKer1:STATe?

:CALCulate:MARKer<n>:Xset / query

Sets the frequency of the specified marker. Queries the frequency of the specified marker.

Name	Type	Values	Description
n	discrete	1 - 8	Specifies which marker to access.
param	real	30 MHz - 1 GHz	Sets the marker frequency.

string - The query returns the frequency of the specified marker in scientific notation.

:CALCulate:MARKer1:X 515000000
:CALCulate:MARKer1:X?

:CALCulate:MARKer<n>:Y?query

Queries the amplitude of the specified marker.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8

:CALCulate:METer:LIMit:ALL:FAIL?query

Queries the measurement results of all the limit lines and their associated meters. If no limit line is set for the meter, the query returns 0; otherwise it returns 0 if all meters are within limit and 1 if the test fails.

integer - Returns 0 if all meters are within the limit and the test is successful, or 1 if the test is failed.

:CALCulate:METer:POWer[:CURRent]?query

Queries the current power of the meter.

real - Returns the current power values of three meters in scientific notation, separated by commas. Returns -1.700000000e+02 for certain filter/detector combinations or when the meter is disabled.

:CALCulate:METer:POWer:PEAK?query

Queries the peak power of the meter. If the meter is disabled, the query returns the minimum data value.

real - The peak power of the meter.

:CALCulate:METer<n>:LIMit[:DATA]set / query

Sets or queries the limits of the specified meter. The query returns the limits of the specified meter in scientific notation.

Name	Type	Values	Description
n	discrete	1 - 3	Specifies the meter number.
ampl	real	dBuV	Current amplitude range limit.

string - Returns the limits of the specified meter in scientific notation.

:CALCulate:METer1:LIMit:DATA 10
:CALCulate:METer1:LIMit:DATA?

:CALCulate:METer<n>:LIMit:FAIL?query

Tests the measurement results of one limit line and its associated specified meter. The query returns 0 if the selected meter is within the limit and 1 if it exceeds the limit line.

Name	Type	Values	Description
n	integer	1 - 3	Specifies the meter number.

enum - Returns 0 when the selected meter is within the limit and the test is successful, or 1 when the selected meter exceeds the limit line and the test fails.

:CALCulate:METer<n>:LIMit:STATeset / query

Enables or disables the limit line of the specified meter. The query reports the limit-line status of the specified meter.

Name	Type	Values	Description
n	discrete	1 - 3	Specifies the meter number.
state	boolean	OFF \| ON \| 0 \| 1	Turns the meter limit line off or on.

integer - The query returns 0 or 1.

:CALCulate:METer1:LIMit:STATe ON or :CALCulate:METer1:LIMit:STATe 1
:CALCulate:METer1:LIMit:STATe?

:CALCulate:DDEMod:MARKer:AOFFset / query

Turns off all the enabled markers.

:CALCulate:DDEMod:MARKer:COUPle[:STATe]set / query

Enables or disables the couple marker function. The query returns the state of the couple marker function.

Name	Type	Values	Description
stateopt	enum	OFF \| ON \| 0 \| 1	Turns the couple marker function on or off.

enum - Returns the couple marker function state as 0 or 1.

:CALCulate:DDEMod:MARKer:COUPle:STATe OFF or :CALCulate:DDEMod:MARKer:COUPle:STATe 0
:CALCulate:DDEMod:MARKer:COUPle:STATe?

:CALCulate:DDEMod:MARKer:TABLe[:STATe]set / query

Enables or disables the marker table. Queries the state of the marker table.

Name	Type	Values	Description
stateopt	enum	OFF \| ON \| 0 \| 1	Turns the marker table on or off.

:CALCulate:DDEMod:MARKer<n>:CPSearch[:STATe]set / query

Enables or disables continuous peak search function, and marks the peak value with Marker N. Queries the status of continuous peak search function.

Name	Type	Values	Description
n	discrete	1 - 8
stateopt	boolean	OFF \| ON \| 0 \| 1	Enables or disables continuous peak search.

integer - The query returns 0 or 1.

:CALCulate:DDEMod:MARKer1:CPSearch:STATe ON or :CALCulate:DDEMod:MARKer1:CPSearch:STATe 1
:CALCulate:DDEMod:MARKer1:CPSearch:STATe?

:CALCulate:DDEMod:MARKer<n>:FUNCtionset / query

Selects the special measurement type for the specified marker. Queries the special measurement type of the specified marker.

Name	Type	Values	Description
n	integer	1 - 8	Marker number.
function	enum	BPOWer \| OFF	Special measurement type to use for the marker.

enum - Returns the special measurement type of the specified marker.

:CALCulate:DDEMod:MARKer1:FUNCtion BPOWer
:CALCulate:DDEMod:MARKer1:FUNCtion?

:CALCulate:DDEMod:MARKer<n>:FUNCtion:BAND:LEFTset / query

Sets the left edge frequency or time of the signal involved in the calculation for the band function. The query returns the left edge frequency or time in scientific notation.

Name	Type	Values	Description
n	integer	1 - 8	Marker number.
real	real	0 - band right	Left edge frequency or time.

real - Returns the left edge frequency or time of the signal involved in the calculation for the band function.

:CALCulate:DDEMod:MARKer1:FUNCtion:BAND:LEFT 2000000
:CALCulate:DDEMod:MARKer1:FUNCtion:BAND:LEFT?

:CALCulate:DDEMod:MARKer<n>:FUNCtion:BAND:RIGHtset / query

Sets the right edge frequency or time of the signal involved in the calculation for the band function. Queries the right edge frequency or time of the signal involved in the calculation for the band function.

Name	Type	Values	Description
<n>	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8
<real>	real	0 - band right	Consecutive real number for the right edge frequency or time.

returns

:CALCulate:DDEMod:MARKer1:FUNCtion:BAND:RIGHt 2000000
:CALCulate:DDEMod:MARKer1:FUNCtion:BAND:RIGHt?

:CALCulate:DDEMod:MARKer<n>:FUNCtion:BAND:SPANset / query

Sets or queries the bandwidth or time span of the signal involved in the calculation for the band function. It is only valid when the marker is open on frequency-domain data and the corresponding bandwidth function is enabled.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number.
freq	real	0 - +∞	Bandwidth or time span value.

real - Returns the bandwidth of the signal involved in the calculation for the band function in scientific notation.

:CALCulate:DDEMod:MARKer1:FUNCtion:BAND:SPAN 500000000
:CALCulate:DDEMod:MARKer1:FUNCtion:BAND:SPAN?

:CALCulate:DDEMod:MARKer<n>:MAXimumset / query

Performs one peak search and marks the found peak with the specified marker. If no peak is found, the instrument displays the prompt message "No peak found".

Name	Type	Values	Description
n	discrete	1 - 8	Marker number to use.

:CALCulate:DDEMod:MARKer2:MAXimum

:CALCulate:DDEMod:MARKer<n>:MAXimum:LEFTset / query

Searches for the nearest peak which is located at the left side of the current peak and marks it with the specified marker.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number to use.

:CALCulate:DDEMod:MARKer2:MAXimum:LEFT

:CALCulate:DDEMod:MARKer<n>:MAXimum:NEXTset / query

Searches for the peak whose amplitude on the trace is next lower than that of the current peak and marks it with the specified marker.

Name	Type	Values	Description
n	enum	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number to use.

:CALCulate:DDEMod:MARKer2:MAXimum:NEXT

:CALCulate:DDEMod:MARKer<n>:MAXimum:PREViousset / query

Searches for the peak whose amplitude on the trace is next higher than that of the current peak and marks it with the specified marker.

Name	Type	Values	Description
<n>	discrete	1 - 8	Marker number.

:CALCulate:DDEMod:MARKer2:MAXimum:PREVious

:CALCulate:DDEMod:MARKer<n>:MAXimum:RIGHtset / query

Searches for the nearest peak located at the right side of the current peak and marks it with the specified marker.

Name	Type	Values	Description
<n>	discrete	1 - 8	Marker number to use for the peak search.

:CALCulate:DDEMod:MARKer2:MAXimum:RIGHt

:CALCulate:DDEMod:MARKer<n>:MINimumset / query

Searches for the peak with the minimum amplitude on the trace and marks it with the specified marker.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number to use.

:CALCulate:DDEMod:MARKer2:MINimum

:CALCulate:DDEMod:MARKer<n>:MODEset / query

Sets the type of the specified marker, or queries the current marker type. The marker can be set to POSition, DELTa, FIXed, or OFF.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.
mode	enum	POSition \| DELTa \| FIXed \| OFF	Marker type to set.

enum - Returns the current marker type as POS, DELT, FIX, or OFF.

:CALCulate:DDEMod:MARKer1:MODE POSition
:CALCulate:DDEMod:MARKer1:MODE?

:CALCulate:DDEMod:MARKer<n>:REFerenceset / query

Sets or queries the reference marker for the specified marker. Each marker can have another marker as its reference marker, and a marker cannot reference itself.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Specifies the marker number.
integer	integer	1 - 8	Sets the reference marker number for the specified marker.

integer - Returns the reference marker number for the specified marker.

:CALCulate:DDEMod:MARKer1:REFerence 2
:CALCulate:DDEMod:MARKer1:REFerence?

:CALCulate:DDEMod:MARKer<n>:TRACeset / query

Sets the marker trace for the specified marker. Queries the marker trace for the specified marker.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8
integer	discrete	1 \| 2 \| 3 \| 4	Marker trace selection, where 1 corresponds to Trace 1 and 4 corresponds to Trace 4.

integer - Returns the marker trace as an integer ranging from 1 to 4.

:CALCulate:DDEMod:MARKer1:TRACe 2

:CALCulate:DDEMod:MARKer<n>:Xset / query

Sets the X-axis value of the specified marker. The default unit is Hz; the query returns the marker's X-axis value in scientific notation.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Specifies which marker to access.
real	real	Hz	Sets the X-axis value of the marker within the available range of the current X axis.

real - Returns the X-axis value of the marker in scientific notation.

The following command sets the X-axis value of Marker 1 to 150 MHz.
:CALCulate:DDEMod:MARKer1:X 150000000
The following query returns 1.500000000e+08.
:CALCulate:DDEMod:MARKer1:X?

:CALCulate:DDEMod:MARKer<n>:Y:IMAGinaryset / query

Sets the selected marker's quadrature component (imaginary) of the Y value. Queries the selected marker's quadrature component (imaginary) of the Y value.

Name	Type	Values	Description
n	integer	1 - 8	Marker number.
real	real	-	Quadrature component (imaginary) of the Y value to set.

real - Returns the selected marker's quadrature component (imaginary) of the Y value.

:CALCulate:DDEMod:MARKer<n>:Y[:REAL]set / query

Sets or queries the Y-axis value of the specified marker. When queried, it returns the marker's Y-axis value or the in-phase component of the Y value in scientific notation.

Name	Type	Values	Description
n	integer	1 - 8	Marker number.
real	real	-	Y-axis value or in-phase component of the Y value.

real - The Y-axis value of the marker or the in-phase component of the Y value in scientific notation.

:CALCulate:DDEMod:MARKer1:Y:REAL 0.325
:CALCulate:DDEMod:MARKer1:Y:REAL?

:CALCulate:MARKer<n>[:SET]:CENTerset / query

Sets the center frequency of the analyzer to the frequency of the specified marker.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Specifies which marker to use.

:CALCulate:MARKer1:SET:CENTer

:CALCulate:MARKer<n>[:SET]:DELTa:CENTerset / query

Sets the center frequency of the analyzer to half of the frequency difference (absolute frequency) between the two Delta markers. It is only valid when the current marker mode is "Delta".

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Marker number.

:CALCulate:MARKer1:SET:DELTa:CENTer

:CALCulate:MARKer<n>[:SET]:RLEVelset / query

Sets the reference level of the analyzer to the amplitude of the specified marker.

Name	Type	Values	Description
n	discrete	1 - 8	Marker number to use.

:CALCulate:MARKer<n>[:SET]:STARtset / query

Sets the start frequency of the analyzer to the frequency of the specified marker. If the marker is in Delta mode, the start frequency is set to the Delta marker frequency.

Name	Type	Values	Description
n	discrete	1 - 8	Specifies which marker is used.

:CALCulate:MARKer3:SET:STARt

:CALCulate:MARKer<n>[:SET]:STEPset / query

Name	Type	Values	Description
n	discrete	1 - 8	Marker number.

:CALCulate:MARKer3:SET:STEP

:CALCulate:MARKer<n>[:SET]:STOPset / query

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8	Specifies the marker number.

:CALCulate:MARKer2:SET:STOP

:TRACe:MATH:PEAK:SORTset / query

Sets the sorting order of the data displayed in the peak table. Queries the current peak-table sorting order.

Name	Type	Values	Description
mode	enum	FREQuency \| AMPLitude	Selects whether peaks are listed by ascending frequency or descending amplitude.

enum - Returns the peak-table sorting order as FREQ or AMPL.

:TRACe:MATH:PEAK:SORT AMPLitude
:TRACe:MATH:PEAK:SORT?

:TRACe:MATH:PEAK:THResholdset / query

Sets the peak criteria that the displayed peak must meet. The query returns the current peak criteria.

Name	Type	Values	Description
mode	enum	NORMal \| DLMore \| DLLess	Peak criteria that the displayed peak must meet.

enum - Returns the current peak criteria as ALL (NORM), GTDL (DLM), or LTDL (DLL).

:TRACe:MATH:PEAK:TABLe:STATeset / query

Enables or disables the peak table. Queries the status of the peak table.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the peak table.

enum - Returns the status of the peak table.

:TRACe:MATH:PEAK:TABLe:STATe OFF|ON|0|1
:TRACe:MATH:PEAK:TABLe:STATe?

:TRACe:AVERage:COUNtset / query

Sets the trace average count of the current measurement. Queries return the average count of the current measurement.

Name	Type	Values	Description
integer	integer	1 - 10,000	Average count value.

:TRACe:AVERage:COUNt:CURRent?query

Queries the current trace average count.

integer - The current trace average count.

:TRACe:CLEar:ALLset / query

Clears all traces, resetting all points on the trace to the minimum value of the trace.

:TRACe[:DATA]set / query

Queries the log data of the specified trace. The returned data format is determined by the :FORMat[:TRACe][:DATA] setting.

Name	Type	Values	Description
trace	enum	TRACE1 \| TRACE2 \| TRACE3	Specifies which trace data to query.

returns - Returns the data of the specified trace. The format of the returned data is determined by the :FORMat[:TRACe][:DATA] command.

:TRACe:DATA? TRACE1.
:TRACe:DATA? TRACE2

:TRACe:MATH:Aset / query

Sets Op1 in the trace math operation formula to Trace 1 through Trace 6. Queries which trace is represented as Op1 in the trace math operation formula.

Name	Type	Values	Description
trace	enum	T1 \| T2 \| T3 \| T4 \| T5 \| T6	Trace selection for Op1 in the trace math operation formula.

enum - Returns which trace is represented as Op1 in the trace math operation formula.

:TRACe:MATH:A T2
:TRACe:MATH:A?

:TRACe:MATH:Bset / query

Sets Op2 in the trace math operation formula to Trace 1 through Trace 6. Queries which trace is Op2 represented in the trace math operation formula.

Name	Type	Values	Description
trace	enum	T1 \| T2 \| T3 \| T4 \| T5 \| T6	Trace selected for Op2.

enum - The query returns the trace selected for Op2.

:TRACe:MATH:B T1
:TRACe:MATH:B?

:TRACe:MATH:CONStset / query

Sets the log offset in the trace math operation formula. Queries the log offset in the trace math operation formula.

Name	Type	Values	Description
integer	real	-100 - 100	Consecutive real number log offset.

real - The query returns the log offset in scientific notation.

:TRACe:MATH:CONSt 50
:TRACe:MATH:CONSt?

:TRACe:MATH:PEAK[:DATA]?query

Queries the frequencies (Hz) and amplitudes (in the current Y-axis unit) of the peaks in the peak table. This command only queries Trace 1.

block - Returns the frequencies and amplitudes of the peaks in the peak table as frequency,amplitude pairs. At most 20 pairs can be returned.

:TRACe:MATH:PEAK:POINts?query

Queries the number of peaks in the peak table.

integer - The number of peaks in the peak table.

:TRACe:MATH:REFerenceset / query

Sets the log reference in the trace math operation formula. Queries the log reference in the trace math operation formula.

Name	Type	Values	Description
integer	real	-170 - 30	Consecutive real number used as the log reference.

string - The query returns the log reference in scientific notation.

:TRACe:MATH:REFerence 50
:TRACe:MATH:REFerence?

:TRACe:MATH:STATeset / query

Enables or disables the math operation of the trace. Queries the status of the math operation of the trace.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the trace math operation.

enum - Returns 0 or 1.

:TRACe:MATH:STATe 1 or :TRACe:MATH:STATe ON
:TRACe:MATH:STATe?

:TRACe:MATH:TYPEset / query

Sets the operation type of the trace. Queries the operation type of the trace.

Name	Type	Values	Description
type	enum	A+B \| A-B \| A+CONST \| A-CONST \| A-B+REF	Operation type of the trace.

enum - The query returns the current trace operation type.

:TRACe:MATH:TYPE A+B
:TRACe:MATH:TYPE?

:TRACe:PRESet:ALLset / query

Resets all the traces. It enables Trace 1 and sets other traces to blank state without affecting trace type or detector type.

:TRACe[:DATA]set / query

Queries the log data of the specified trace. The returned data format is determined by the :FORMat[:TRACe][:DATA] setting.

Name	Type	Values	Description
trace	enum	TRACE1 \| TRACE2 \| TRACE3	Specifies which trace data to query.

returns - Returns the data of the specified trace. The format of the returned data is determined by the :FORMat[:TRACe][:DATA] command.

:TRACe:DATA? TRACE1.
:TRACe:DATA? TRACE2

:CALibration:[ALL]set / query

Executes self-calibration immediately.

:CALibration:ALL

:CALibration:AUTOset / query

Enables or disables auto calibration. The query returns the setting status of auto calibration.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Auto calibration state.

enum - Returns 0 or 1 indicating the auto calibration setting status.

:CALibration:AUTO ON or :CALibration:AUTO 1
:CALibration:AUTO?

:CALibration:[ALL]set / query

Executes self-calibration immediately.

:CALibration:ALL

:CALibration:AUTOset / query

Enables or disables auto calibration. The query returns the setting status of auto calibration.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Auto calibration state.

enum - Returns 0 or 1 indicating the auto calibration setting status.

:CALibration:AUTO ON or :CALibration:AUTO 1
:CALibration:AUTO?

:CALibration:[ALL]set / query

Executes self-calibration immediately.

:CALibration:ALL

:CALibration:AUTOset / query

Enables or disables auto calibration. The query returns the setting status of auto calibration.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Auto calibration state.

enum - Returns 0 or 1 indicating the auto calibration setting status.

:CALibration:AUTO ON or :CALibration:AUTO 1
:CALibration:AUTO?

:CONFigure?query

Queries the current measurement function.

enum - Returns the current measurement function.

:CONFigure:ACPowerset / query

Sets the analyzer to be in the ACP measurement state. This command is only available for GPSA mode and restores the specified measurement to the default factory state.

:CONFigure:CNRatioset / query

Sets the analyzer to be in the CNR measurement state.

:CONFigure:DENSityset / query

Sets the analyzer to be in the Density measurement state.

:CONFigure:DSPEctrogramset / query

Sets the analyzer to be in the Density Spectrogram measurement state. This command is only available for RTSA mode.

:CONFigure:EBWidthset / query

Sets the analyzer to be in the EBW measurement state.

:CONFigure:HDIStset / query

Sets the analyzer to be in the harmonic distortion measurement state.

:CONFigure:LPSTepset / query

Resets all the parameters in the current measurement mode.

:CONFigure:MCHPowerset / query

Sets the analyzer to be in the MCHP measurement state.

:CONFigure:NORMalset / query

Sets the analyzer to be in the Normal measurement state.

:CONFigure:OBWidthset / query

Sets the analyzer to be in the OBW measurement state.

:CONFigure:PSGRamset / query

Sets the analyzer to be in the PvT Spectrogram measurement state. This command is only available for RTSA mode and restores the specified measurement to the default factory state.

:CONFigure:PSPectrumset / query

Sets the analyzer to be in the PvT Spectrum measurement state. This command is only available for RTSA mode and will discontinue the current measurement, restoring the specified measurement to the default factory state.

:CONFigure:PVTset / query

Sets the analyzer to be in the PvT measurement state. This command is only available for RTSA mode and will discontinue the current measurement, restoring the specified measurement to the default factory state.

:CONFigure:SANalyzerset / query

Sets the analyzer to swept SA mode. This command is only available in GPSA mode and disables the currently activated measurement function.

:CONFigure:SPECtrogramset / query

Sets the analyzer to be in the Spectrogram measurement state.

:CONFigure:TOIset / query

Sets the analyzer to be in the TOI measurement state.

:CONFigure:TPOWerset / query

Sets the analyzer to be in the time-domain power measurement state.

:CONFigure?query

Queries the current measurement function.

enum - Returns the current measurement function.

:CONFigure:FSCanset / query

Sets the spectrum analyzer to the frequency scanning measurement state.

:CONFIgure:BERateset / query

Sets the analyzer to be in the bit error rate measurement state.

:CONFigure:DDEModset / query

Sets the analyzer to be in the digital demodulation measurement state.

:COUPleset / query

Sets all the manual/auto settings in the current measurement mode to Auto.

:COUPleset / query

Sets all the manual/auto settings in the current measurement mode to Auto.

:DISPlay:BACKlightset / query

Sets the brightness of the LCD backlight. The query returns the current backlight brightness.

Name	Type	Values	Description
integer	integer	1 - 100	Brightness level of the backlight.

integer - The brightness of the LCD backlight.

:DISPlay:BACKlight 50
:DISPlay:BACKlight?

:DISPlay:ENABleset / query

Turns on or off the LCD. Queries the status of the LCD.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the LCD on or off.

:DISPlay:ENABle ON or :DISPlay:ENABle 1
:DISPlay:ENABle?

:DISPlay:GRATicule[:STATe]set / query

Enables or disables the display of the graticule. Queries the display of the graticule.

Name	Type	Values	Description
stateopt	boolean	OFF \| ON \| 0 \| 1	Sets the graticule display state.

integer - Returns 0 or 1 indicating the graticule display state.

:DISPlay:GRATicule:STATe ON or :DISPlay:GRATicule:STATe 1
:DISPlay:GRATicule:STATe?

:DISPlay:HDMI[:STATe]set / query

Enables or disables HDMI output. Queries the status of HDMI output.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns HDMI output on or off.

integer - The query returns 0 or 1.

:DISPlay:HDMI:STATe ON or :DISPlay:HDMI:STATe 1
:DISPlay:HDMI:STATe?

:DISPlay:PVTime:WINDow:TRACe:X[:SCALe]:COUPleset / query

Enables or disables the auto scale function for the horizontal axis in the PvT view. Queries the status of the auto scale function for the horizontal axis in the PvT view.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns auto scale for the horizontal axis in the PvT view off or on.

enum - The query returns 1 or 0.

:DISPlay:PVTime:WINDow:TRACe:X:SCALe:COUPle ON
:DISPlay:PVTime:WINDow:TRACe:X:SCALe:COUPle 1
:DISPlay:PVTime:WINDow:TRACe:X:SCALe:COUPle?

:DISPlay:PVTime:WINDow:TRACe:X[:SCALe]:PDIVisionset / query

Sets the unit per division in the horizontal axis of the PvT view. Queries the unit per division in the horizontal axis of the PvT view.

Name	Type	Values	Description
time	real	20 μs - 4 s	Consecutive real number specifying the horizontal axis scale per division.

string - Returns the X-axis scale value in scientific notation.

:DISPlay:PVTime:WINDow:TRACe:X:SCALe:PDIVision 0.00004

:DISPlay:PVTime:WINDow:TRACe:X[:SCALe]:RLEVelset / query

Sets the reference time for the horizontal axis in the PvT view. Queries the reference time for the horizontal axis in the PvT view.

Name	Type	Values	Description
real	real	-1 s - 40 s	Consecutive real number reference time for the horizontal axis in the PvT view.

string - The query returns the reference time for the horizontal axis in scientific notation.

:DISPlay:PVTime:WINDow:TRACe:X:SCALe:RLEVel 2
:DISPlay:PVTime:WINDow:TRACe:X:SCALe:RLEVel?

:DISPlay:PVTime:WINDow:TRACe:X[:SCALe]:RPOSitionset / query

Sets the position of the reference time in the horizontal axis of the PvT view. Queries the position of the reference time in the horizontal axis of the PvT view.

Name	Type	Values	Description
mode	enum	LEFT \| CENTer \| RIGHt	Position of the reference time on the horizontal axis.

enum - Returns the reference-time position as LEFT, CENT, or RIGH.

:DISPlay:PVTime:WINDow:TRACe:X:SCALe:RPOSition LEFT
:DISPlay:PVTime:WINDow:TRACe:X:SCALe:RPOSition?

:DISPlay:PVTime:WINDow:TRACe:Y[:SCALe]:PDIVisionset / query

Sets the unit per division in the vertical axis of the PvT view. Queries the unit per division in the vertical axis of the PvT view.

Name	Type	Values	Description
rel_ampl	real	0.1 dB - 20 dB	Unit per division for the vertical axis of the PvT view.

real - Returns the Y-axis scale value in scientific notation.

:DISPlay:PVTime:WINDow:TRACe:Y:SCALe:PDIVision 15
:DISPlay:PVTime:WINDow:TRACe:Y:SCALe:PDIVision?

:DISPlay:VIEW:DENSity:AADJustset / query

Sets the highest density hue to the highest density value found in the current bitmap, and the lowest density hue to the lowest non-zero density value found in the current bitmap. This command is only available for Density and Density Spectrogram in RTSA mode.

:DISPlay:VIEW:DENSity:CNONlinearset / query

Sets or queries the curve nonlinearity for Density and Density Spectrogram in RTSA mode. Increasing the value compresses colors toward the higher end of the color bar; decreasing it compresses them toward the lower end.

Name	Type	Values	Description
real	real	-100 - 100	Consecutive real number value for the curve nonlinearity.

real - Returns the curve nonlinearity value in scientific notation.

:DISPlay:VIEW:DENSity:CNONlinear 50
:DISPlay:VIEW:DENSity:CNONlinear?

:DISPlay:VIEW:DENSity:CPALettesset / query

Sets or queries the color palette of Density. This command is only available for Density and Density Spectrogram in RTSA mode.

Name	Type	Values	Description
palette	enum	COOL \| WARM \| RADar \| FIRE \| FROSt	Color palette for Density.

enum - The query returns the current Density color palette as COOL, WARM, RAD, FIRE, or FROS.

:DISPlay:VIEW:DENSity:CPALettes COOL
:DISPlay:VIEW:DENSity:CPALettes?

:DISPlay:VIEW:DENSity:HDHueset / query

Sets the highest density hue. Queries the highest density hue.

Name	Type	Values	Description
real	real	0.1 - 100	Consecutive real number for the highest density hue.

real - The query returns the highest density hue in scientific notation.

:DISPlay:VIEW:DENSity:HDHue 60
:DISPlay:VIEW:DENSity:HDHue?

:DISPlay:VIEW:DENSity:LDHueset / query

Sets the lowest density hue and queries the lowest density hue. This command is only available for Density and Density Spectrogram in RTSA mode.

Name	Type	Values	Description
real	real	0 - 99.9	Lowest density hue value.

real - The query returns the lowest density hue in scientific notation.

:DISPlay:VIEW:DENSity:LDHue 30
:DISPlay:VIEW:DENSity:LDHue?

:DISPlay:VIEW:DENSity:PERSistenceset / query

Sets the persistence time. Queries the persistence time.

Name	Type	Values	Description
time	real	0 s - 10 s	Consecutive real number specifying the persistence time.

real (s) - The query returns the persistence time in scientific notation.

:DISPlay:VIEW:DENSity:PERSistence 5
:DISPlay:VIEW:DENSity:PERSistence?

:DISPlay:VIEW:DENSity:PERSistence:INFiniteset / query

Enables or disables the infinite mode of the persistence time. Queries the status of the infinite mode of the persistence time.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the infinite mode of the persistence time.

enum - Returns the status of the infinite mode of the persistence time as 0 or 1.

:DISPlay:VIEW:DENSity:PERSistence:INFinite ON or :DISPlay:VIEW:DENSity:PERSistence:INFinite 1
:DISPlay:VIEW:DENSity:PERSistence:INFinite?

:DISPlay:VIEW[:SELect]set / query

Sets the current display view. Queries the current display view.

Name	Type	Values	Description
view	enum	NORMal \| SPECtrogram \| DENSity \| DSPectrogram \| PVT \| PVTSpectrum \| PSPectrogram	Display view to select.

enum - Returns the current display view as an abbreviated keyword.

:DISPlay:VIEW[:SELect] NORMal|SPECtrogram|DENSity|DSPectrogram|PVT|PVTSpectrum|PSPectrogram
:DISPlay:VIEW[:SELect]?

:DISPlay:VIEW:SPECtrogram:AADJustset / query

Auto adjusts the reference hue position and bottom hue position based on the highest and lowest amplitude values found in the spectrogram, respectively.

:DISPlay:VIEW:SPECtrogram:BOTTomset / query

Sets the bottom hue position displayed in the graticule, or queries the current bottom hue position. Any amplitudes lower than this position are displayed as black.

Name	Type	Values	Description
integer	integer	0 - min (90%, with the reference position value -10%)	Bottom hue position displayed in the graticule.

integer - Queries the bottom hue position displayed in the graticule in integer.

:DISPlay:VIEW:SPECtrogram:BOTTom 40
:DISPlay:VIEW:SPECtrogram:BOTTom?

:DISPlay:VIEW:SPECtrogram:HUEset / query

Sets the reference hue for the spectrogram color bar. Queries the current reference hue value.

Name	Type	Values	Description
real	real	0 - 359.9	Consecutive real number specifying the reference hue.

real - Returns the reference hue value in scientific notation.

:DISPlay:VIEW:SPECtrogram:HUE 120
:DISPlay:VIEW:SPECtrogram:HUE?

:DISPlay:VIEW:SPECtrogram:POSitionset / query

Sets the trace to be displayed in the spectrogram. Queries the displayed trace number.

Name	Type	Values	Description
integer	integer	1 - 8,192	Trace number to display in the spectrogram.

integer - The displayed trace number.

:DISPlay:VIEW:SPECtrogram:POSition 146

:DISPlay:VIEW:SPECtrogram:REFerenceset / query

Sets the position of the reference hue displayed in the graticule. The query returns the reference hue position displayed in the graticule as an integer.

Name	Type	Values	Description
integer	integer	Max (10%, bottom hue value +10%) - 100	Reference hue position in the graticule.

integer - Reference hue position displayed in the graticule.

:DISPlay:VIEW:SPECtrogram:REFerence 60
:DISPlay:VIEW:SPECtrogram:REFerence?

:DISPlay:VIEW:SPECtrogram:TRACe:COUPleset / query

Enables or disables coupling the marker to the trace. On keeps the marker on the selected trace and changes with the trace; Off fixes the current marker to the displayed trace that is active when the marker is turned on.

Name	Type	Values	Description
state	enum	ON \| OFF \| 1 \| 0	Enables or disables trace coupling.

enum - Returns 0 or 1 indicating whether the marker is coupled to the trace.

:DISPlay:VIEW:SPECtrogram:TRACe:COUPle ON|OFF|1|0
:DISPlay:VIEW:SPECtrogram:TRACe:COUPle?

:DISPlay:VIEW:SPECtrogram:TRACe:SELectionset / query

Sets the selection method for the displayed trace, or queries the current selection method. This command is only available for Spectrogram in RTSA mode or in a view that contains the spectrogram.

Name	Type	Values	Description
mode	enum	TIME \| TNUMber	Selection method for the displayed trace.

enum - Returns the selection method for the displayed trace.

:DISPlay:VIEW:SPECtrogram:TRACe:SELection TIME
:DISPlay:VIEW:SPECtrogram:TRACe:SELection?

:DISPlay:WINDow:SELectset / query

Selects a window in the current view. Queries the currently selected window type.

Name	Type	Values	Description
window type	enum	SPECtrum \| PVT	Selects the window type.

enum - The currently selected window type is returned as SPEC or PVT.

::DISPlay:WINDow:SELect PVT
::DISPlay:WINDow:SELect?

:DISPlay:WINDow:TRACe:Y:DLINeset / query

Sets the position of the display line. The query returns the display line position in scientific notation.

Name	Type	Values	Description
ampl	real	dBuV	Consecutive real number within the current amplitude range.

string - Returns the position of the display line in scientific notation.

:DISPlay:WINDow:TRACe:Y:DLINe -10
:DISPlay:WINDow:TRACe:Y:DLINe?

:DISPlay:WINDow:TRACe:Y:DLINe:STATeset / query

Turns the display line on or off. Queries the status of the display line.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the display line on or off.

:DISPlay:WINdow:TRACe:Y:DLINe:STATe ON or :DISPlay:WINdow:TRACe:Y:DLINe:STATe 1
:DISPlay:WINdow:TRACe:Y:DLINe:STATe?

:DISPlay:WINDow:TRACe:Y[:SCALe]:NRLevelset / query

Sets the reference level of normalization. Queries the reference level of normalization.

Name	Type	Values	Description
rel_ampl	real	-200 - 200	Consecutive real number specifying the normalization reference level.

real - Returns the reference level of normalization in scientific notation.

:DISPlay:WINDow:TRACe:Y:SCALe:NRLevel -20
:DISPlay:WINDow:TRACe:Y:SCALe:NRLevel?

:DISPlay:WINDow:TRACe:Y[:SCALe]:NRPositionset / query

Sets the reference position of normalization. Queries the reference position of normalization.

Name	Type	Values	Description
integer	integer	0% - 100%	Reference position of normalization.

integer - The query returns the reference position of normalization in integer.

:DISPlay:WINDow:TRACe:Y:SCALe:NRPosition 50
:DISPlay:WINDow:TRACe:Y:SCALe:NRPosition?

:DISPlay:WINDow:TRACe:Y[:SCALe]:PDIVisionset / query

Sets the Y-axis scale type. Queries the Y-axis scale value.

Name	Type	Values	Description
rel_ampl	real	0.1 dB - 20 dB	Y-axis scale value.

real - The query returns the Y-axis scale value in scientific notation.

:DISPlay:WINDow:TRACe:Y:SCALe:PDIVision 15
:DISPlay:WINDow:TRACe:Y:SCALe:PDIVision?

:DISPlay:WINDow:TRACe:Y[:SCALe]:RLEVelset / query

Sets the reference level and queries the reference level.

Name	Type	Values	Description
ampl	real	-170 - 30	Reference level amplitude.

real - The query returns the reference level in scientific notation.

:DISPlay:WINDow:TRACe:Y:SCALe:RLEVel -10
:DISPlay:WINDow:TRACe:Y:SCALe:RLEVel?

:DISPlay:WINDow:TRACe:Y[:SCALe]:RLEVel:OFFSetset / query

Sets the reference level offset. Queries the reference level offset.

Name	Type	Values	Description
rel_ampl	real	-300 dB - 300 dB	Relative amplitude offset applied to the reference level.

:DISPlay:WINDow:TRACe:Y:SCALe:RLEVel:OFFSet 10
:DISPlay:WINDow:TRACe:Y:SCALe:RLEVel:OFFSet?

:DISPlay:WINDow:TRACe:Y[:SCALe]:SPACingset / query

Sets the Y-axis scale type or queries the current Y-axis scale type.

Name	Type	Values	Description
mode	enum	LINear \| LOGarithmic	Selects the Y-axis scale type.

enum - The query returns the Y-axis scale type as LIN or LOG.

:DISPlay:WINDow:TRACe:Y:SCALe:SPACing LOGarithmic
:DISPlay:WINDow:TRACe:Y:SCALe:SPACing?

:DISPlay:BACKlightset / query

Sets the brightness of the LCD backlight. The query returns the current backlight brightness.

Name	Type	Values	Description
integer	integer	1 - 100	Brightness level of the backlight.

integer - The brightness of the LCD backlight.

:DISPlay:BACKlight 50
:DISPlay:BACKlight?

:DISPlay:ENABleset / query

Turns on or off the LCD. Queries the status of the LCD.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the LCD on or off.

:DISPlay:ENABle ON or :DISPlay:ENABle 1
:DISPlay:ENABle?

:DISPlay:FSCan:VIEW:METer:FLINeset / query

Enables or disables the display of the meter frequency line. Queries the display status of the meter frequency line.

Name	Type	Values	Description
state	boolean	OFF \| ON \| 0 \| 1	Controls whether the meter frequency line is displayed.

integer - Returns the display status of the meter frequency line as 0 or 1.

:DISPlay:FSCan:VIEW:METer:FLINe ON
:DISPlay:FSCan:VIEW:METer:FLINe?

:DISPlay:FSCan:VIEW:METer[:STATe]set / query

Enables or disables the display of the meter window. Queries the display status of the meter window.

Name	Type	Values	Description
stateopt	enum	OFF \| ON \| 0 \| 1	Enables or disables the meter window display state.

enum - The query returns 0 or 1.

:DISPlay:FSCan:VIEW:METer:STATe ON or :DISPlay:FSCan:VIEW:METer:STATe 1
:DISPlay:FSCan:VIEW:METer:STATe?

:DISPlay:FSCan:VIEW:WINDow:TRACe:Y[:SCALe]:PDIVisionset / query

Sets the Y-axis scale type. Queries the Y-axis scale type.

Name	Type	Values	Description
rel_ampl	real	0.1 dB - 20 dB	Consecutive real number that sets the Y-axis scale value.

string - The query returns the Y-axis scale value in scientific notation.

:DISPlay:FSCan:VIEW:WINDow:TRACe:Y:SCALe:PDIVision 15
:DISPlay:FSCan:VIEW:WINDow:TRACe:Y:SCALe:PDIVision?

:DISPlay:FSCan:VIEW:WINDow:TRACe:Y[:SCALe]:RLEVelset / query

Sets the reference level. Queries the reference level.

Name	Type	Values	Description
real	real	-63.01 - 136.99	Consecutive real number reference level.

real - The query returns the reference level in scientific notation.

:DISPlayy:FSCan:VIEW:WINDow:TRACe:Y:SCALe:RLEVel 100
:DISPlayy:FSCan:VIEW:WINDow:TRACe:Y:SCALe:RLEVel?

:DISPlay:FSCan:VIEW:WINDow:TRACe:Y[:SCALe]:RLEVel:OFFSetset / query

Sets the reference level offset and queries the current offset. The offset only modifies the reference level and amplitude readout of the marker, not the curve position.

Name	Type	Values	Description
rel_ampl	real	-300 - 300	Reference level offset.

string - Returns the offset of the reference level in scientific notation.

:DISPlay:FSCan:VIEW:WINDow:TRACe:Y:SCALe:RLEVel:OFFSet 10
:DISPlay:FSCan:VIEW:WINDow:TRACe:Y:SCALe:RLEVel:OFFSet?

:DISPlay:FSCan:WINDow:MAMarker[:STATe]set / query

Enables or disables the display of the measurement window at the marker. Queries the display status of the measurement window at the marker.

Name	Type	Values	Description
stateopt	enum	OFF \| ON \| 0 \| 1	Display state of the measurement window at the marker.

:DISPlay:FSCan:WINDow:MAMarker:STATe ON or :DISPlay:FSCan:WINDow:MAMarker:STATe 1
:DISPlay:FSCan:WINDow:MAMarker:STATe?

:DISPlay:GRATicule[:STATe]set / query

Enables or disables the display of the graticule. Queries the display of the graticule.

Name	Type	Values	Description
stateopt	boolean	OFF \| ON \| 0 \| 1	Sets the graticule display state.

integer - Returns 0 or 1 indicating the graticule display state.

:DISPlay:GRATicule:STATe ON or :DISPlay:GRATicule:STATe 1
:DISPlay:GRATicule:STATe?

:DISPlay:HDMI[:STATe]set / query

Enables or disables HDMI output. Queries the status of HDMI output.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns HDMI output on or off.

integer - The query returns 0 or 1.

:DISPlay:HDMI:STATe ON or :DISPlay:HDMI:STATe 1
:DISPlay:HDMI:STATe?

:DISPlay:METer<n>[:STATe]set / query

Enables or disables the specified meter. The query returns the status of the specified meter.

Name	Type	Values	Description
stateopt	enum	OFF \| ON \| 0 \| 1	Enables or disables the specified meter.

enum - The query returns 0 or 1.

:DISPlay:METer2:STATe ON
:DISPlay:METer2:STATe 1
:DISPlay:METer2:STATe?

:DISPlay:VIEW:WINDow:TRACe:X:SPACingset / query

Sets the scale type of the X-axis. Queries the scale type of the X-axis.

enum - Returns the X-axis scale type.

:DISPlay:VIEW:WINDow:TRACe:X:SPACing LINear
:DISPlay:VIEW:WINDow:TRACe:X:SPACing?

:DISPlay:WINDow:TRACe:Y:DLINeset / query

Sets the position of the display line. The query returns the display line position in scientific notation.

Name	Type	Values	Description
ampl	real	dBuV	Consecutive real number within the current amplitude range.

string - Returns the position of the display line in scientific notation.

:DISPlay:WINDow:TRACe:Y:DLINe -10
:DISPlay:WINDow:TRACe:Y:DLINe?

:DISPlay:WINDow:TRACe:Y:DLINe:STATeset / query

Turns the display line on or off. Queries the status of the display line.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the display line on or off.

:DISPlay:WINdow:TRACe:Y:DLINe:STATe ON or :DISPlay:WINdow:TRACe:Y:DLINe:STATe 1
:DISPlay:WINdow:TRACe:Y:DLINe:STATe?

:DISPlay[:WINDow]:TRACe<n>:MODEset / query

Sets the type of the specified trace. Queries the type of the specified trace.

Name	Type	Values	Description
n	discrete	1 - 3	Specifies the trace number.
mode	enum	WRITe \| AVERage \| MAXHold \| MINHold	Sets the trace type to write, average, maximum hold, or minimum hold.

enum - Returns the trace type in abbreviated form.

:DISPlay:WINDow:TRACe1:MODE MAXHold
:DISPlay:WINDow:TRACe1:MODE?

:DISPlay:BACKlightset / query

Sets the brightness of the LCD backlight. The query returns the current backlight brightness.

Name	Type	Values	Description
integer	integer	1 - 100	Brightness level of the backlight.

integer - The brightness of the LCD backlight.

:DISPlay:BACKlight 50
:DISPlay:BACKlight?

:DISPlay:DDEMod:TRACe<n>:DDEMod:EYE:COUNtset / query

Sets the eye length of the specified trace. Queries the eye length of the specified trace.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4	Trace number to select.
count	real	1 - 40	Eye length setting for the specified trace.

real - The query returns the eye length of the specified trace in scientific notation.

:DISPlay:DDEMod:TRACe1:DDEMod:EYE:COUNt 3
:DISPlay:DDEMod:TRACe1:DDEMod:EYE:COUNt?

:DISPlay:DDEMod:TRACe<n>:DDEMod:SYMBol:FORMatset / query

Sets or queries the symbol format of the specified trace.

Name	Type	Values	Description
n	integer	1 - 4	Specifies the trace number.
format	enum	HEXadecimal \| BINary	Selects the symbol format.

enum - Returns the symbol format of the specified trace as HEX or BIN.

:DISPlay:DDEMod:TRACe1:DDEMod:SYMBol:FORMat BINary
:DISPlay:DDEMod:TRACe1:DDEMod:SYMBol:FORMat?

:DISPlay:DDEMod:TRACe<n>:FEEDset / query

Sets the data source of the specified trace. Queries the data source of the specified trace.

Name	Type	Values	Description
<n>	discrete	1 - 4
source	enum	CTIMe \| CSPEctrum \| MTIMe \| MSPEctrum \| RTIMe \| RSPEctrum \| EVTime \| EVSpectrum \| IQMError \| IQPError \| SYMBol \| SUMMary \| RTTrace

returns - The query returns the data source of the specified trace.

:DISPlay:DDEMod:TRACe1:FEED SYMBol

:DISPlay:DDEMod:TRACe<n>:FORMatset / query

Sets the display format of the specified trace. The query returns the current display format.

Name	Type	Values	Description
<n>	discrete	1 - 4	Specifies the trace number.
format	enum	IEYE \| QEYE \| CONS \| MLOG \| REAL \| IMAGinary \| VECTor \| PHASe \| UPHas \| MLINear	Sets the display format of the specified trace.

enum - Returns the current display format of the specified trace.

:DISPlay:DDEMod:TRACe1:FORMat CONS
:DISPlay:DDEMod:TRACe1:FORMat?

:DISPlay:DDEMod:TRACe<n>:X[:SCALe]:COUPleset / query

Enables or disables the X Scale auto mode of the specified trace. Queries the status of the X Scale auto mode for the specified trace.

Name	Type	Values	Description
n	integer	1 - 4	Specifies the trace number.
state	enum	OFF \| ON \| 0 \| 1	Turns X Scale auto mode off or on.

enum - Returns the status of the X Scale auto mode for the specified trace.

:DISPlay:DDEMod:TRACe<n>:X[:SCALe]:RLEVelset / query

Sets or queries the X-axis reference of the selected trace. This command is valid only when the X-axis scale is set to Manual.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4	Selects the trace number.
real	real	-1e+12 - 1e+12	Sets the X-axis reference value for the selected trace.

real (s or Hz) - Returns the X-axis reference of the selected trace in scientific notation.

:DISPlay:DDEMod:TRACe1:X:SCALe:RLEVel 25
:DISPlay:DDEMod:TRACe1:X:SCALe:RLEVel?

:DISPlay:DDEMod:TRACe<n>:X[:SCALe]:RPOSitionset / query

Sets the position from which the X-axis scale reference value is calculated for the specified trace. The query returns that position for the specified trace.

Name	Type	Values	Description
n	discrete	1 - 4
mode	enum	LEFT \| CENTer \| RIGHt	Position from which the X-axis scale reference value is calculated.

enum - Returns the X-axis scale reference position for the specified trace.

:DISPlay:DDEMod:TRACe1:X:SCALe:RPOSition LEFT
:DISPlay:DDEMod:TRACe1:X:SCALe:RPOSition?

:DISPlay:DDEMod:TRACe<n>:X[:SCALe]:SPANset / query

Sets the X-axis width of the selected trace. The query returns the X-axis width of the selected trace in scientific notation.

Name	Type	Values	Description
<n>	discrete	1 - 4
<real>	real	0 - 1e+12	Consecutive real number specifying the X-axis width. Time-domain data uses 0 to 1e+12, and frequency-domain data uses 0 Hz to 1 THz.

real - The X-axis width of the selected trace in scientific notation.

:DISPlay:DDEMod:TRACe1:X:SCALe:SPAN 50

:DISPlay:DDEMod:TRACe<n>:Y[:SCALe]:AUTO:ONCEset / query

Sets the Y-axis reference level and the Y-axis scale value automatically to ensure that the signal can be fully displayed for better observation of the trace.

Name	Type	Values	Description
n	discrete	1 - 4

:DISPlay:DDEMod:TRACe1:Y:SCALe:AUTO:ONCE

:DISPlay:DDEMod:TRACe<n>:Y[:SCALe]:PDIVisionset / query

Sets the Y-axis scale of the specified trace. The query returns the Y-axis scale value in scientific notation.

Name	Type	Values	Description
<n>	discrete	1 \| 2 \| 3 \| 4	Trace number.
<rel>	real	-1e+09 - 1e+12	Y-axis scale value.

real - Returns the Y-axis scale value in scientific notation.

:DISPlay:DDEMod:TRACe1:Y:SCALe:PDIVision 0.3
:DISPlay:DDEMod:TRACe1:Y:SCALe:PDIVision?

:DISPlay:DDEMod:TRACe<n>:Y[:SCALe]:RLEVelset / query

Sets the Y-axis reference of the specified trace. The query returns the reference in scientific notation.

Name	Type	Values	Description
n	discrete	1 - 4	Specifies the trace number.
ampl	real	-1e+12 - 1e+12	Sets the Y-axis reference value.

real - The reference value in scientific notation.

:DISPlay:DDEMod:TRACe1:Y:SCALe:RLEVel -10
:DISPlay:DDEMod:TRACe1:Y:SCALe:RLEVel?

:DISPlay:DDEMod:TRACe<n>:Y:UNIT:PREFerenceset / query

Sets the Y-axis unit of the specified trace. Queries the Y-axis unit of the specified trace.

Name	Type	Values	Description
n	integer	1 - 4
mode	enum	PEAK \| RMS \| POWer	Selects the Y-axis unit preference.

enum - Returns the current Y-axis unit preference.

:DISPlay:DDEMod:TRACe1:Y:UNIT:PREFerence PEAK
:DISPlay:DDEMod:TRACe1:Y:UNIT:PREFerence?

:DISPlay:DDEMod:WINDow:FORMatset / query

Sets the trace window layout. Queries the trace window layout.

Name	Type	Values	Description
mode	enum	SINGle \| LRWindow \| UDWindow \| LRDWindow \| UDRWindow \| QUAD	Trace window layout to use.

enum - Returns the current trace window layout as SING, LRW, UDW, LRDW, UDRW, or QUAD.

:DISPlay:DDEMod:WINDow:FORMat SINGle
:DISPlay:DDEMod:WINDow:FORMat?

:DISPlay:ENABleset / query

Turns on or off the LCD. Queries the status of the LCD.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the LCD on or off.

:DISPlay:ENABle ON or :DISPlay:ENABle 1
:DISPlay:ENABle?

:DISPlay:GRATicule[:STATe]set / query

Enables or disables the display of the graticule. Queries the display of the graticule.

Name	Type	Values	Description
stateopt	boolean	OFF \| ON \| 0 \| 1	Sets the graticule display state.

integer - Returns 0 or 1 indicating the graticule display state.

:DISPlay:GRATicule:STATe ON or :DISPlay:GRATicule:STATe 1
:DISPlay:GRATicule:STATe?

:DISPlay:HDMI[:STATe]set / query

Enables or disables HDMI output. Queries the status of HDMI output.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns HDMI output on or off.

integer - The query returns 0 or 1.

:DISPlay:HDMI:STATe ON or :DISPlay:HDMI:STATe 1
:DISPlay:HDMI:STATe?

:FETCh:ACPower?query

Queries the results of adjacent channel power measurement. It selects data from the latest measurement results and transmits them to the output buffer.

numeric - Returns 5 values: main channel power, upper channel power, power difference between upper channel and main channel (in dBc), lower channel power, and power difference between lower channel and main channel (in dBc), all in scientific notation and separated by commas.

:FETCh:ACPower?

:FETCh:ACPower:LOWer?query

Queries the lower channel power of the adjacent channel power measurement. It returns the lower channel power from the latest measurement results in scientific notation.

real - Lower channel power in scientific notation; the power unit is consistent with the current Y-axis unit.

:FETCh:ACPower:LOWer?

:FETCh:ACPower:MAIN?query

Queries the main channel power of the adjacent channel power measurement. It returns the latest measured main channel power in scientific notation.

real (dB) - Returns the main channel power in scientific notation.

.FETCh:ACPower:MAIN?

:FETCh:ACPower:UPPer?query

Queries the upper channel power of the adjacent channel power measurement. It returns the latest measured upper channel power in scientific notation, with units matching the current Y-axis unit.

real - The upper channel power in scientific notation.

:FETCh:ACPower:UPPer?
:FETCh:ACPower:UPPer?

:FETCh:CNRatio?query

Queries the results of C/N ratio measurement. It selects data from the latest measurement results and transmits them to the output buffer.

numeric (dB) - Returns the carrier power, noise power, and C/N ratio in scientific notation, separated by commas.

:FETCh:CNRatio:CARRier?query

Queries the carrier power from the latest C/N ratio measurement results. It is only valid when C/N ratio measurement in GPSA mode is enabled.

real - Returns the carrier power in scientific notation.

:FETCh:CNRatio:CARRier?

:FETCh:CNRatio:CNRatio?query

Queries the results of C/N ratio measurement. It selects data from the latest measurement results and transmits it to the output buffer.

real - Returns the C/N ratio in scientific notation.

FETCh:CNRatio:CNRatio?

:FETCh:CNRatio:NOISe?query

Queries the noise power. It selects data from the latest measurement results and transmits it to the output buffer.

real - Returns the noise power in scientific notation. The power unit is consistent with the current Y-axis unit.

FETCh:CNRatio:NOISe?

:FETCh:EBWidth?query

Queries the result of the emission bandwidth measurement. It selects data from the latest measurement results and transmits the data to the output buffer.

integer (Hz) - Returns the emission bandwidth.

:FETCh:EBWidth?

:FETCh:HARMonics:AMPLitude:ALL?query

Queries the amplitudes of the first 10 harmonics. The first harmonic is the fundamental waveform.

real (consistent with current Y-axis unit) - Returns the amplitudes of the first 10 harmonics in scientific notation, separated by commas. If fewer than 10 harmonics are being measured, unmeasured harmonics have no return values.

:FETCh:HARMonics:AMPLitude:ALL?

:FETCh:HARMonics[:DISTortion]?query

Queries the percentage of the total harmonic distortion. It selects data from the latest measurement results and transmits the data to the output buffer.

real - The percentage of the total harmonic distortion, returned in scientific notation.

*No example for the exact optional-node mnemonic; the manual shows `:FETCh:HARMonics:DISTortion?` as the invocation line.*

:FETCh:HARMonics:FREQuency:ALL?query

Queries the frequencies of the first 10 harmonics. The first harmonic is the fundamental waveform.

real (Hz) - Returns the frequencies of the first 10 harmonics in scientific notation, separated by commas; unmeasured harmonics are omitted. The unit is Hz.

:FETCh:HARMonics:FREQuency:ALL?

:FETCh:HARMonics:FUNDamental?query

Queries the frequency of the fundamental waveform. It selects data from the latest measurement results and transmits it to the output buffer.

real (Hz) - Returns the frequency of the fundamental waveform in scientific notation.

FETCh:HARMonics:FUNDamental?

:FETCh:OBWidth?query

Queries the results of the occupied bandwidth measurement. It selects data from the latest measurement results and transmits them to the output buffer.

string (Hz) - Returns the occupied bandwidth (Hz) and the transmit frequency error (Hz) in scientific notation, separated by commas.

:FETCh:OBWidth?

:FETCh:OBWidth:OBWidth?query

Queries the occupied bandwidth. It selects data from the latest measurement results and transmits the data to the output buffer.

real (Hz) - Returns the occupied bandwidth in scientific notation.

:FETCh:OBWidth:OBWidth?

:FETCh:OBWidth:OBWidth:FERRor?query

Queries the transmit frequency error. It selects data from the latest occupied bandwidth measurement results and transmits it to the output buffer.

real (Hz) - The transmit frequency error in scientific notation.

.FETCh:OBWidth:OBWidth:FERRor?

:FETCh:SANalyzer<n>?query

Queries the measurement results or trace data in the cache area. The command returns the measurement data of Trace n in scientific notation as x,y pairs separated by commas.

Name	Type	Values	Description
n	discrete	1 - 6	Trace number to read from the cache area.

string (Hz) - Measurement data of Trace n returned in scientific notation as x,y pairs separated by commas.

:FETCh:SANalyzer1?

:FETCh:TOIntercept?query

Queries the results of TOI measurement. The command returns the latest TOI measurement data from the output buffer when TOI measurement in GPSA mode is enabled.

numeric (Hz) - Returns the TOI measurement results as Base Lower frequency (Hz), amplitude, Base Upper frequency (Hz), amplitude, 3rd Order Lower frequency (Hz), amplitude, intercept, 3rd Order Upper frequency (Hz), amplitude, intercept.

:FETCh:TOIntercept?

:FETCh:TOIntercept:IP3?query

Returns the minor value of the intercepts of the Third Order Lower and Third Order Upper. It selects data from the latest measurement results and transmits it to the output buffer.

real - Returns the minor one in scientific notation.

":FETCh:TOIntercept:IP3?" returns -8.131735000e+01.

:FETCh:TPOWer?query

Queries the result of T-power measurement. It selects data from the latest measurement results and transmits the data to the output buffer.

real - Returns the T-power measurement result in scientific notation; the power unit is consistent with the current Y-axis unit.

:FETCh:FSCan?query

Queries the frequency scan measurement results. Returns the signal table information.

string - Returns the signal table information.

:FETCh:BER?query

Queries the bit error rate measurement results.

returns - Bit error rate measurement results.

:FETCh:DDEMod?query

Queries the digital demodulation measurement results.

returns - Returns the digital demodulation measurement results.

:FORMat:BORDerset / query

Selects the binary data byte order for data transmission. Queries the binary data byte order for data transmission.

Name	Type	Values	Description
mode	enum	NORMal \| SWAPped	Binary data byte order for data transmission.

enum - Returns the binary data byte order for data transmission.

:FORMat:BORDer NORMal
:FORMat:BORDer?

:FORMat[:TRACe][:DATA]set / query

Sets the input/output format of the trace data. Queries the input/output format of the trace data.

Name	Type	Values	Description
mode	enum	ASCii \| INTeger,32 \| REAL,32 \| REAL,64	Selects the trace data input/output format.

enum - Returns the current trace data input/output format as one of ASC,8, INT,32, REAL,32, or REAL,64.

:FORMat:TRACe:DATA REAL,32
:FORMat:TRACe:DATA?

:FORMat:BORDerset / query

Selects the binary data byte order for data transmission. Queries the binary data byte order for data transmission.

Name	Type	Values	Description
mode	enum	NORMal \| SWAPped	Binary data byte order for data transmission.

enum - Returns the binary data byte order for data transmission.

:FORMat:BORDer NORMal
:FORMat:BORDer?

:FORMat[:TRACe][:DATA]set / query

Sets the input/output format of the trace data. Queries the input/output format of the trace data.

Name	Type	Values	Description
mode	enum	ASCii \| INTeger,32 \| REAL,32 \| REAL,64	Selects the trace data input/output format.

enum - Returns the current trace data input/output format as one of ASC,8, INT,32, REAL,32, or REAL,64.

:FORMat:TRACe:DATA REAL,32
:FORMat:TRACe:DATA?

:FORMat:BORDerset / query

Selects the binary data byte order for data transmission. Queries the binary data byte order for data transmission.

Name	Type	Values	Description
mode	enum	NORMal \| SWAPped	Binary data byte order for data transmission.

enum - Returns the binary data byte order for data transmission.

:FORMat:BORDer NORMal
:FORMat:BORDer?

:FORMat[:TRACe][:DATA]set / query

Sets the input/output format of the trace data. Queries the input/output format of the trace data.

Name	Type	Values	Description
mode	enum	ASCii \| INTeger,32 \| REAL,32 \| REAL,64	Selects the trace data input/output format.

enum - Returns the current trace data input/output format as one of ASC,8, INT,32, REAL,32, or REAL,64.

:FORMat:TRACe:DATA REAL,32
:FORMat:TRACe:DATA?

*CLSset / query

Clears all the event registers and status byte registers.

*ESEset / query

Sets or queries the enable register for the standard event status register.

Name	Type	Values	Description
value	integer	0 - 255	Integer value written to the enable register.

integer - The query returns the register contents as an integer equal to the binary-weighted sum of the bits set in the register.

*ESE 16
*ESE?

*ESR?query

Queries and clears the event register for the standard event status register.

integer - Returns an integer corresponding to the binary-weighted sum of all bits set in the standard event status register. Bit 1 and bit 6 are always 0; the value ranges from 0 to 255.

*ESR?

*IDN?query

Queries the ID string of the instrument.

string - Returns the ID string in the format Rigol Technologies,<model>,<serial number>,XX.XX.XX.

*IDN?

*OPCset / query

Sets bit 0 (Operation Complete, OPC) in the standard event status register to 1 after the current operation is finished. Queries whether the current operation is finished.

integer - The query returns 1 after the current operation is finished; otherwise, the query returns 0.

*RCLset / query

Recalls the selected register.

Name	Type	Values	Description
integer	integer	1 - 16	Register number to recall.

*RCL 1

*RSTset / query

Restores the instrument to its factory default settings.

*SAVset / query

Saves the current instrument state to the selected register.

Name	Type	Values	Description
integer	integer	1 - 16	Register number to save the current instrument state to.

*SAV 1

*SREset / query

Sets the enable register for the status byte register, and the query reads back that register value.

Name	Type	Values	Description
value	integer	0 - 255	Enable-register value. Bit 0 and Bit 1 are always treated as 0.

integer - Returns the enable register as an integer equal to the binary-weighted sum of all bits set in the register.

*SRE 16
*SRE?

*STB?query

Queries the event register for the status byte register. The query returns a decimal integer corresponding to the enabled bits in the register.

integer - Returns the status byte register as an integer value from 0 to 255, equal to the binary-weighted sum of all bits set in the register.

*STB?

*TRGset / query

Triggers a sweep or measurement immediately.

*TST?query

Queries whether the self-check operation is finished. The query returns 0 if the test is successful and 1 if it fails.

integer - 0 indicates the self-check operation was successful; 1 indicates it failed.

*WAIset / query

Waits for the current operation to finish.

:INITiate:CONTinuousset / query

Selects continuous (ON|1) or single (OFF|0) sweep mode. The query returns the current sweep mode.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Sets the sweep mode to continuous or single.

enum - Returns the current sweep mode as 0 or 1.

:INITiate:CONTinuous ON or :INITiate:CONTinuous 1
:INITiate:CONTinuous?

:INITiate[:IMMediate]set / query

In non-measurement state, initializes a sweep. In measurement state, triggers a measurement.

:INITiate:FSCan:CLEar:IMMediateset / query

Deletes all the signals in the signal table and launches the selected scan sequence.

:INITiate:PAUSeset / query

Pauses scan, search, or the final measurement.

:INITiate:RESumeset / query

Resumes scanning from the scan point where it was paused.

:INITiate:BER:RESTartset / query

Restarts the BER test. This command is valid only when the BER Test measurement function is selected.

:INITiate:CONTinuousset / query

Selects continuous (ON|1) or single (OFF|0) sweep mode. The query returns the current sweep mode.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Sets the sweep mode to continuous or single.

enum - Returns the current sweep mode as 0 or 1.

:INITiate:CONTinuous ON or :INITiate:CONTinuous 1
:INITiate:CONTinuous?

:INSTrument:COUPle:FREQuency:CENTerset / query

Turns on or off the global center frequency of the instrument. Queries the setting status of the global center frequency of the instrument.

Name	Type	Values	Description
state	enum	ALL \| NONE	Turns the global center frequency on or off.

:INSTrument:COUPle:FREQuency:CENTer ALL
:INSTrument:COUPle:FREQuency:CENTer?

:INSTrument:DEFaultset / query

Resets the parameters of the current mode to the factory default settings.

:INSTrument:NSELectset / query

Selects the working mode of the instrument. The query returns the current working mode.

Name	Type	Values	Description
mode	enum	1 \| 2 \| 3 \| 4	Selects the working mode by discrete numeric code.

enum - Returns the current working mode as a discrete code or corresponding keyword.

:INSTrument:NSELect 3
:INSTrument:NSELect?

:INSTrument[:SELect]set / query

Selects the working mode of the instrument. The query returns the current working mode.

Name	Type	Values	Description
mode	enum	SA \| RTSA \| VSA \| EMI	Working mode to select.

enum - Returns the current working mode.

:INSTrument:SELect VSA
:INSTrument:SELect?

:INSTrument:COUPle:FREQuency:CENTerset / query

Turns on or off the global center frequency of the instrument. Queries the setting status of the global center frequency of the instrument.

Name	Type	Values	Description
state	enum	ALL \| NONE	Turns the global center frequency on or off.

:INSTrument:COUPle:FREQuency:CENTer ALL
:INSTrument:COUPle:FREQuency:CENTer?

:INSTrument:DEFaultset / query

Resets the parameters of the current mode to the factory default settings.

:INSTrument:NSELectset / query

Selects the working mode of the instrument. The query returns the current working mode.

Name	Type	Values	Description
mode	enum	1 \| 2 \| 3 \| 4	Selects the working mode by discrete numeric code.

enum - Returns the current working mode as a discrete code or corresponding keyword.

:INSTrument:NSELect 3
:INSTrument:NSELect?

:INSTrument[:SELect]set / query

Selects the working mode of the instrument. The query returns the current working mode.

Name	Type	Values	Description
mode	enum	SA \| RTSA \| VSA \| EMI	Working mode to select.

enum - Returns the current working mode.

:INSTrument:SELect VSA
:INSTrument:SELect?

:INSTrument:COUPle:FREQuency:CENTerset / query

Turns on or off the global center frequency of the instrument. Queries the setting status of the global center frequency of the instrument.

Name	Type	Values	Description
state	enum	ALL \| NONE	Turns the global center frequency on or off.

:INSTrument:COUPle:FREQuency:CENTer ALL
:INSTrument:COUPle:FREQuency:CENTer?

:INSTrument:DEFaultset / query

Resets the parameters of the current mode to the factory default settings.

:INSTrument:NSELectset / query

Selects the working mode of the instrument. The query returns the current working mode.

Name	Type	Values	Description
mode	enum	1 \| 2 \| 3 \| 4	Selects the working mode by discrete numeric code.

enum - Returns the current working mode as a discrete code or corresponding keyword.

:INSTrument:NSELect 3
:INSTrument:NSELect?

:INSTrument[:SELect]set / query

Selects the working mode of the instrument. The query returns the current working mode.

Name	Type	Values	Description
mode	enum	SA \| RTSA \| VSA \| EMI	Working mode to select.

enum - Returns the current working mode.

:INSTrument:SELect VSA
:INSTrument:SELect?

:MMEMory:DELeteset / query

Deletes a specified file.

Name	Type	Values	Description
file_name	string	-	Path and filename of the file to delete.

:MMEMory:DELete /vsa/state/state1.sta

:MMEMory:LOAD:CORRectionset / query

Loads the data from the specified .csv file to carry out amplitude correction.

Name	Type	Values	Description
mode	enum	1 \| 2 \| 3 \| 4	Selects which correction data to load: ANTenna, CABLe, OTHer, or USER.
file_name	string	-	Name of the correction file to load.

:MMEMory:LOAD:CORRection 1,ANT.csv

:MMEMory:LOAD:FMTset / query

Loads the edited FMT file (.csv).

Name	Type	Values	Description
label	enum	UPPer \| LOWer
file_name	string	-

:MMEMory:LOAD:LIMitset / query

Loads the edited limit line file (.csv).

Name	Type	Values	Description
label	string	-
file_name	string	-

:MMEMory:LOAD:STATeset / query

Loads the specified state file (.sta).

Name	Type	Values	Description
file_name	string	-	State file to load.

::MMEMory:LOAD:STATe state1.sta

:MMEMory:LOAD:TRACeset / query

Loads the specified trace file (.trs) and the current instrument state.

Name	Type	Values	Description
label	enum	TRACE1 \| TRACE2 \| TRACE3	Trace label to load.
file_name	string	-	Name of the trace file to load.

:MMEMory:LOAD:TRACe TRACE2,t1.trs

:MMEMory:LOAD:TRACe:DATAset / query

Loads the specified measurement data file (.csv) into the selected trace. The operation fails if the specified file does not exist.

Name	Type	Values	Description
label	enum	TRACE1 \| TRACE2 \| TRACE3 \| TRACE4	Selects which trace receives the measurement data.
file_name	string	-	Specifies the measurement data file name.

:MMEMory:LOAD:TRACe:DATA TRACE1,trace1.csv

:MMEMory:MOVEset / query

Renames the specified file <file_name1> as <file_name2>. Both arguments should include the path and filename; the operation fails if the source file does not exist.

Name	Type	Values	Description
file_name1	string	-	Source file name, including path and filename.
file_name2	string	-	Destination file name, including path and filename.

:MMEMory:MOVE /vsa/state/state1.sta,/vsa/state/state2.sta

:MMEMory:STORe:CORRectionset / query

Saves the amplitude correction data file to the default path ("/"mode name"/correction") with the specified filename, which is suffixed with ".csv" by default.

Name	Type	Values	Description
mode	enum	1 \| 2 \| 3 \| 4	Selects which correction data to save; 1\|2\|3\|4 correspond to ANTenna\|CABLe\|OTHer\|USER.
file_name	string	-	Filename to use when saving the correction data.

:MMEMory:STORe:LIMitset / query

Saves the currently edited limit line with the specified filename suffixed with ".csv" by default to the default path (/<mode name>/limit). If the file already exists, it is overwritten.

Name	Type	Values	Description
label	enum	LLINE1 \| LLINE2 \| LLINE3 \| LLINE4 \| LLINE5 \| LLINE6	Limit line identifier to save.
file_name	string	-	Filename to use for the saved CSV file.

:MMEMory:STORe:LIMit LLINE1,low

:MMEMory:STORe:MTABleset / query

Saves the marker table to a specified filename suffixed with ".csv" by default in the default path ("/mode name"/measdata). If the specified file already exists, it is overwritten.

Name	Type	Values	Description
file_name	string	-	ASCII string filename to use for the saved marker table.

:MMEMory:STORe:MTABle <file_name>

:MMEMory:STORe:PTABleset / query

Saves the peak table with a specified filename suffixed with ".csv" by default to the default path (/"mode name"/measdata). If the file already exists, it is overwritten.

Name	Type	Values	Description
file_name	string	-	Filename for the peak table to save.

:MMEMory:STORe:PTABle PT1

:MMEMory:STORe:RESultsset / query

Saves the current measurement results with a specified filename suffixed with ".csv" by default to the default path (/"mode name"/measdata). If the specified file already exists, it is overwritten. The command is only valid when the advanced measurement function in GPSA mode is enabled.

Name	Type	Values	Description
file_name	string	-	Filename to use for saving the measurement results.

:MMEMory:STORe:RESults data

:MMEMory:STORe:SCReenset / query

Saves the current screen image with the specified filename suffixed with ".jpg", ".png", or ".bmp" to the default path ("/mode name"/screen).

Name	Type	Values	Description
file_name	string	-	Filename for the saved screen image.

:MMEMory:STORe:SCReen <file_name>

:MMEMory:STORe:STATeset / query

Saves the current instrument state with the specified filename suffixed with ".sta" to the default path (/("mode name")/state). If the specified file already exists, it is overwritten.

Name	Type	Values	Description
file_name	string	-	Filename for the saved instrument state.

:MMEMory:STORe:STATe state

:MMEMory:STORe:TRACeset / query

Saves the specified trace+state file with the filename suffixed with ".trs" to the default path ("/mode name"/tracestate). If the specified file already exists, it is overwritten.

Name	Type	Values	Description
label	enum	TRACE1 \| TRACE2 \| TRACE3	Trace label to save.
file_name	string	-	Filename to use for the saved trace+state file.

:MMEMory:STORe:TRACe TRACE1,mystate

:MMEMory:STORe:TRACe:DATAset / query

Saves the trace measurement results to a CSV file in the default data path. The file is named with the specified filename suffixed with ".csv".

Name	Type	Values	Description
label	enum	TRACE1 \| TRACE2 \| TRACE3 \| TRACE4	Selects which trace measurement results to save.
file_name	string	-	Filename to use for the saved CSV data.

:MMEMory:DELeteset / query

Deletes a specified file.

Name	Type	Values	Description
file_name	string	-	Path and filename of the file to delete.

:MMEMory:DELete /vsa/state/state1.sta

:MMEMory:LOAD:CORRectionset / query

Loads the data from the specified .csv file to carry out amplitude correction.

Name	Type	Values	Description
mode	enum	1 \| 2 \| 3 \| 4	Selects which correction data to load: ANTenna, CABLe, OTHer, or USER.
file_name	string	-	Name of the correction file to load.

:MMEMory:LOAD:CORRection 1,ANT.csv

:MMEMory:LOAD:LIMitset / query

Loads the edited limit line file (.csv).

Name	Type	Values	Description
label	string	-
file_name	string	-

:MMEMory:LOAD:SCANset / query

Loads the specified scan table file (.csv).

Name	Type	Values	Description
file_name	string	-	Name of the scan table file to load.

:MMEMory:LOAD:SCAN scan.csv

:MMEMory:LOAD:SLIStset / query

Loads the specified signal table file (.csv).

Name	Type	Values	Description
file_name	string	-	ASCII string file name of the signal table to load.

::MMEMory:LOAD:SLISt slist.csv

:MMEMory:LOAD:STATeset / query

Loads the specified state file (.sta).

Name	Type	Values	Description
file_name	string	-	State file to load.

::MMEMory:LOAD:STATe state1.sta

:MMEMory:LOAD:TRACeset / query

Loads the specified trace file (.trs) and the current instrument state.

Name	Type	Values	Description
label	enum	TRACE1 \| TRACE2 \| TRACE3	Trace label to load.
file_name	string	-	Name of the trace file to load.

:MMEMory:LOAD:TRACe TRACE2,t1.trs

:MMEMory:LOAD:TRACe:DATAset / query

Loads the specified measurement data file (.csv) into the selected trace. The operation fails if the specified file does not exist.

Name	Type	Values	Description
label	enum	TRACE1 \| TRACE2 \| TRACE3 \| TRACE4	Selects which trace receives the measurement data.
file_name	string	-	Specifies the measurement data file name.

:MMEMory:LOAD:TRACe:DATA TRACE1,trace1.csv

:MMEMory:MOVEset / query

Renames the specified file <file_name1> as <file_name2>. Both arguments should include the path and filename; the operation fails if the source file does not exist.

Name	Type	Values	Description
file_name1	string	-	Source file name, including path and filename.
file_name2	string	-	Destination file name, including path and filename.

:MMEMory:MOVE /vsa/state/state1.sta,/vsa/state/state2.sta

:MMEMory:STORe:CORRectionset / query

Saves the amplitude correction data file to the default path ("/"mode name"/correction") with the specified filename, which is suffixed with ".csv" by default.

Name	Type	Values	Description
mode	enum	1 \| 2 \| 3 \| 4	Selects which correction data to save; 1\|2\|3\|4 correspond to ANTenna\|CABLe\|OTHer\|USER.
file_name	string	-	Filename to use when saving the correction data.

:MMEMory:STORe:LIMitset / query

Saves the currently edited limit line with the specified filename suffixed with ".csv" by default to the default path (/<mode name>/limit). If the file already exists, it is overwritten.

Name	Type	Values	Description
label	enum	LLINE1 \| LLINE2 \| LLINE3 \| LLINE4 \| LLINE5 \| LLINE6	Limit line identifier to save.
file_name	string	-	Filename to use for the saved CSV file.

:MMEMory:STORe:LIMit LLINE1,low

:MMEMory:STORe:SCANset / query

Saves the scan table with a specified filename suffixed with ".csv" by default to the default path (/<mode name>/scantable). If the specified file already exists, it is overwritten.

Name	Type	Values	Description
file_name	string	-	Filename to use for the saved scan table.

:MMEMory:STORe:SCAN scantable1

:MMEMory:STORe:SCReenset / query

Saves the current screen image with the specified filename suffixed with ".jpg", ".png", or ".bmp" to the default path ("/mode name"/screen).

Name	Type	Values	Description
file_name	string	-	Filename for the saved screen image.

:MMEMory:STORe:SCReen <file_name>

:MMEMory:STORe:SLIStset / query

Saves the signal table with a specified filename suffixed with ".csv" by default to the default path (/{"mode name"}/signaltable). If the specified file already exists, it is overwritten.

Name	Type	Values	Description
file_name	string	-	Filename for the signal table to save.

The following command saves the signal table with the filename "signaltable1" to the folder (/emi/signaltable). :MMEMory:STORe:SLISt signaltable1

:MMEMory:STORe:STATeset / query

Saves the current instrument state with the specified filename suffixed with ".sta" to the default path (/("mode name")/state). If the specified file already exists, it is overwritten.

Name	Type	Values	Description
file_name	string	-	Filename for the saved instrument state.

:MMEMory:STORe:STATe state

:MMEMory:STORe:TRACeset / query

Saves the specified trace+state file with the filename suffixed with ".trs" to the default path ("/mode name"/tracestate). If the specified file already exists, it is overwritten.

Name	Type	Values	Description
label	enum	TRACE1 \| TRACE2 \| TRACE3	Trace label to save.
file_name	string	-	Filename to use for the saved trace+state file.

:MMEMory:STORe:TRACe TRACE1,mystate

:MMEMory:STORe:TRACe:DATAset / query

Saves the trace measurement results to a CSV file in the default data path. The file is named with the specified filename suffixed with ".csv".

Name	Type	Values	Description
label	enum	TRACE1 \| TRACE2 \| TRACE3 \| TRACE4	Selects which trace measurement results to save.
file_name	string	-	Filename to use for the saved CSV data.

:MMEMory:DELeteset / query

Deletes a specified file.

Name	Type	Values	Description
file_name	string	-	Path and filename of the file to delete.

:MMEMory:DELete /vsa/state/state1.sta

:MMEMory:LOAD:FMTset / query

Loads the edited FMT file (.csv).

Name	Type	Values	Description
label	enum	UPPer \| LOWer
file_name	string	-

:MMEMory:LOAD:STATeset / query

Loads the specified state file (.sta).

Name	Type	Values	Description
file_name	string	-	State file to load.

::MMEMory:LOAD:STATe state1.sta

:MMEMory:LOAD:TRACe:DATAset / query

Loads the specified measurement data file (.csv) into the selected trace. The operation fails if the specified file does not exist.

Name	Type	Values	Description
label	enum	TRACE1 \| TRACE2 \| TRACE3 \| TRACE4	Selects which trace receives the measurement data.
file_name	string	-	Specifies the measurement data file name.

:MMEMory:LOAD:TRACe:DATA TRACE1,trace1.csv

:MMEMory:MOVEset / query

Renames the specified file <file_name1> as <file_name2>. Both arguments should include the path and filename; the operation fails if the source file does not exist.

Name	Type	Values	Description
file_name1	string	-	Source file name, including path and filename.
file_name2	string	-	Destination file name, including path and filename.

:MMEMory:MOVE /vsa/state/state1.sta,/vsa/state/state2.sta

:MMEMory:STORe:FMTset / query

Saves the FMT file with the specified filename suffixed with ".csv" to the default path (/<mode name>/mask). If the file already exists, it is overwritten.

Name	Type	Values	Description
label	enum	UPPer \| LOWer	Selects whether to save the upper or lower mask FMT file.
file_name	string	-	Specifies the output filename.

:MMEMory:STORe:FMT UPPer,mask1

:MMEMory:STORe:SCReenset / query

Saves the current screen image with the specified filename suffixed with ".jpg", ".png", or ".bmp" to the default path ("/mode name"/screen).

Name	Type	Values	Description
file_name	string	-	Filename for the saved screen image.

:MMEMory:STORe:SCReen <file_name>

:MMEMory:STORe:STATeset / query

Saves the current instrument state with the specified filename suffixed with ".sta" to the default path (/("mode name")/state). If the specified file already exists, it is overwritten.

Name	Type	Values	Description
file_name	string	-	Filename for the saved instrument state.

:MMEMory:STORe:STATe state

:MMEMory:STORe:TRACe:DATAset / query

Saves the trace measurement results to a CSV file in the default data path. The file is named with the specified filename suffixed with ".csv".

Name	Type	Values	Description
label	enum	TRACE1 \| TRACE2 \| TRACE3 \| TRACE4	Selects which trace measurement results to save.
file_name	string	-	Filename to use for the saved CSV data.

:OUTPut[:EXTernal][:STATe]set / query

Enables or disables the output of the tracking generator. Queries the on/off status of the tracking generator.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the tracking generator output.

enum - The query returns 0 or 1.

:OUTPut:EXTernal:STATe ON or :OUTPut:EXTernal:STATe 1
:OUTPut:EXTernal:STATe?

:READ:ACPower?query

Executes one adjacent channel power measurement and returns the measurement results. The command is only available in GPSA mode.

numeric - Returns five values in scientific notation: main channel power, upper channel power, the power difference between the upper channel and the main channel in dBc, lower channel power, and the power difference between the lower channel and the main channel in dBc.

:READ:ACPower?

:READ:ACPower:LOWer?query

Executes one adjacent channel power measurement and returns the lower channel power. The return value uses the current Y-axis unit and is only available in GPSA mode.

real - Returns the lower channel power in scientific notation using the current Y-axis unit.

:READ:ACPower:MAIN?query

Executes one adjacent channel power measurement and returns the main channel power. The power unit of the returned value is consistent with the current Y-axis unit; the command is only available in GPSA mode.

real - Returns the main channel power in scientific notation.

:READ:ACPower:MAIN?

:READ:ACPower:UPPer?query

Executes one adjacent channel power measurement and returns the upper channel power. This command is only available in GPSA mode.

real - Returns the upper channel power in scientific notation.

:READ:CNRatio?query

Executes one C/N ratio measurement and returns the measurement results.

numeric (dB) - Returns the carrier power, noise power, and C/N ratio in scientific notation, separated by commas.

:READ:CNRatio:CARRier?query

Executes one C/N ratio measurement and returns the carrier power.

real (dB) - Returns the carrier power in scientific notation.

:READ:CNRatio:CNRatio?query

Executes one C/N ratio measurement and returns the C/N ratio.

real - Returns the C/N ratio in scientific notation.

:READ:CNRatio:CNRatio?

:READ:CNRatio:NOISe?query

Executes one C/N ratio measurement and returns the noise power.

real - Returns the noise power in scientific notation. The power unit of the return value is consistent with the current Y-axis unit.

:READ:EBWidth?query

Executes one emission bandwidth measurement and returns the measurement results. This command is only available for GPSA mode.

real (Hz) - Returns the emission bandwidth measurement results in scientific notation.

:READ:HARMonics:AMPLitude:ALL?query

Executes one harmonic distortion measurement and returns the amplitudes of the first 10 harmonics. The amplitudes are returned in scientific notation, separated by commas, and use the current Y-axis unit.

real - Returns the amplitudes of the first 10 harmonics in scientific notation, separated by commas. If fewer than 10 harmonics are measured, the unmeasured harmonics have no return values.

:READ:HARMonics:AMPLitude:ALL?

:READ:HARMonics[:DISTortion]?query

Executes one harmonic distortion measurement and returns the percentage of the total harmonic distortion.

real (%) - Returns the percentage of the total harmonic distortion in scientific notation.

:READ:HARMonics:FREQuency:ALL?query

Executes one harmonic distortion measurement and returns the frequencies of the first 10 harmonics. This command is only available for GPSA mode.

block (Hz) - The query returns the frequencies in scientific notation (separated by commas). The unit is Hz.

:READ:HARMonics:FREQuency:ALL?

:READ:HARMonics:FUNDamental?query

Executes one harmonic distortion measurement and returns the frequency of the fundamental waveform. It is only available for GPSA mode and selects data from the latest measurement results for transmission to the output buffer.

real (Hz) - Returns the frequency of the fundamental waveform in scientific notation.

:READ:OBWidth?query

Executes one occupied bandwidth measurement and returns the measurement results. The query selects data from the latest measurement results and transmits it to the output buffer; it is only available in GPSA mode.

real (Hz) - Returns the occupied bandwidth and the transmit frequency error in scientific notation, separated by commas.

:READ:OBWidth:OBWidth?query

Executes one occupied bandwidth measurement and returns the occupied bandwidth. It selects data from the latest measurement results and is only available in GPSA mode.

real (Hz) - The occupied bandwidth in scientific notation.

:READ:OBWidth:OBWidth:FERRor?query

Executes one occupied bandwidth measurement and returns the transmit frequency error. It selects data from the latest measurement results and is only available in GPSA mode.

real (Hz) - The query returns the transmit frequency error in scientific notation.

:READ:SANalyzer<n>?query

Queries the measurement results or trace data in the buffer for trace n. It selects data from the latest measurement results and transmits it to the output buffer.

Name	Type	Values	Description
n	discrete	1 \| 2 \| 3 \| 4 \| 5 \| 6	Trace number to read.

block (Hz) - Returns the measurement data of Trace n in scientific notation as paired (x,y) data separated by commas.

:FETCh:SANalyzer1?

:READ:TOIntercept?query

Executes one TOI measurement and returns the measurement results. The command is only available in GPSA mode.

string - Returns TOI measurement results as comma-separated values: Base Lower frequency (Hz), amplitude, Base Upper frequency (Hz), amplitude, 3rd Order Lower frequency (Hz), amplitude, intercept, 3rd Order Upper frequency (Hz), amplitude, intercept.

:READ:TOIntercept:IP3?query

Executes one TOI measurement and returns the value of the intercept of the Third Order Lower or the Third Order Upper, whichever is smaller. It selects data from the latest measurement results and transmits the data to the output buffer; available only in GPSA mode.

real - Returns the minor one in scientific notation.

:READ:TPOWer?query

Executes one T-power measurement and returns the measurement results. The returned power value is in scientific notation and its unit is consistent with the current Y-axis unit.

real - Returns the T-power measurement result in scientific notation.

:READ:TPOWer?

:TRACe<n>:AVERage:TYPEset / query

Selects the average type of the swept SA analysis measurement. Queries the average type of the swept SA analysis measurement.

Name	Type	Values	Description
n	discrete	1 - 6	Trace number.
type	enum	LOG \| RMS \| SCALar	Average type to use for the swept SA analysis measurement.

enum - Returns the current average type.

:TRACe1:AVERage:TYPE LOG
:TRACe1:AVERage:TYPE?

:TRACe<n>:DISPlay:STATeset / query

Enables or disables the display of the specified trace. Queries the status for the specified trace.

Name	Type	Values	Description
n	integer	1 - 6	Specifies the trace number.
state	boolean	OFF \| ON \| 0 \| 1	Enables or disables trace display.

integer - Returns 1 if the specified trace display is enabled, or 0 if it is disabled.

:TRACe1:DISPlay:STATe ON
:TRACe1:DISPlay:STATe 1
:TRACe1:DISPlay:STATe?

:TRACe<n>:MODEset / query

Sets the type of the specified trace. Queries the type of the specified trace.

Name	Type	Values	Description
n	integer	1 - 6	Specifies the trace number.
mode	enum	WRITe \| AVERage \| MAXHold \| MINHold	Selects the trace type.

enum - Returns the type of the specified trace.

:TRACe<n>:TYPEset / query

Sets the type of the specified trace. Queries the type of the specified trace.

Name	Type	Values	Description
n	integer	1 - 6	Trace number.
mode	enum	WRITe \| AVERage \| MAXHold \| MINHold	Trace type to select.

enum - Returns the type of the specified trace.

:TRACe1:TYPE WRITe
:TRACe1:TYPE?

:TRACe<n>:UPDate:STATeset / query

Enables or disables the update of the specified trace. Queries the setting state for the update of the specified trace.

Name	Type	Values	Description
n	discrete	1 - 3	Specifies the trace number.
state	boolean	OFF \| ON \| 0 \| 1	Enables or disables trace update.

integer - The query returns 1 or 0.

:TRACe1:UPDate:STATe ON or :TRACe1:UPDate:STATe 1
:TRACe1:UPDate:STATe?

:TRACe<n>:DISPlay[:STATe]set / query

Enables or disables the display of the specified trace. Queries the setting state for the specified trace.

Name	Type	Values	Description
n	discrete	1 - 3	Trace number.
state	boolean	OFF \| ON \| 0 \| 1	Display state for the specified trace.

enum - The query returns 1 or 0.

:TRACe1:DISPlay:STATe ON or :TRACe1:DISPlay:STATe 1
:TRACe1:DISPlay:STATe?

:TRACe<n>:UPDate:STATeset / query

Enables or disables the update of the specified trace. Queries the setting state for the update of the specified trace.

Name	Type	Values	Description
n	discrete	1 - 3	Specifies the trace number.
state	boolean	OFF \| ON \| 0 \| 1	Enables or disables trace update.

integer - The query returns 1 or 0.

:TRACe1:UPDate:STATe ON or :TRACe1:UPDate:STATe 1
:TRACe1:UPDate:STATe?

:TRACe<n>[:DATA]?query

Queries the data of the specified trace. The returned data format is determined by :FORMat[:TRACe][:DATA].

Name	Type	Values	Description
n	discrete	1 - 4	Specifies the trace number.

returns - The data of the specified trace, in the format selected by :FORMat[:TRACe][:DATA].

:TRACe1:DATA?
:TRACe2:DATA?

:INPut:IMPedanceset / query

Sets the input impedance for voltage-to-power conversion. Queries the input impedance for voltage-to-power conversion; the unit is Ω.

Name	Type	Values	Description
impedance	enum	50 \| 75	Selects the input impedance.

enum - Returns 50 or 75.

:INPut:IMPedance 75 or :SENSe:CORRection:IMPedance:INPut:MAGnitude 75
:INPut:IMPedance? or :SENSe:CORRection:IMPedance:INPut:MAGnitude?

:INPut:IMPedanceset / query

Sets the input impedance for voltage-to-power conversion. Queries the input impedance for voltage-to-power conversion; the unit is Ω.

Name	Type	Values	Description
impedance	enum	50 \| 75	Selects the input impedance.

enum - Returns 50 or 75.

:INPut:IMPedance 75 or :SENSe:CORRection:IMPedance:INPut:MAGnitude 75
:INPut:IMPedance? or :SENSe:CORRection:IMPedance:INPut:MAGnitude?

:INPut:IMPedanceset / query

Sets the input impedance for voltage-to-power conversion. Queries the input impedance for voltage-to-power conversion; the unit is Ω.

Name	Type	Values	Description
impedance	enum	50 \| 75	Selects the input impedance.

enum - Returns 50 or 75.

:INPut:IMPedance 75 or :SENSe:CORRection:IMPedance:INPut:MAGnitude 75
:INPut:IMPedance? or :SENSe:CORRection:IMPedance:INPut:MAGnitude?

:SOURce:CORRection:OFFSetset / query

Sets the offset of the tracking generator output amplitude. The query returns the offset in scientific notation; the value affects only the readout, not the actual output power.

Name	Type	Values	Description
rel_ampl	real	-200 - 200	Offset of the output amplitude of the tracking generator.

:SOURce:CORRection:OFFSet 10
:SOURce:CORRection:OFFSet?

:SOURce[:EXTernal]:POWer[:LEVel][:IMMediate][:AMPLitude]set / query

Sets the output amplitude of the tracking generator. Queries the output amplitude of the tracking generator.

Name	Type	Values	Description
ampl	real	-40 dBm - 0 dBm	Output amplitude of the tracking generator.

real (dBm) - The query returns the output amplitude of the tracking generator.

:SOURce:TRACe:REFerence:STATeset / query

Sets whether to display the reference trace of normalization. Queries whether to display the reference trace of normalization.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Controls whether the reference trace of normalization is displayed.

enum - Returns 0 or 1.

::SOURce:TRACe:REF:STATe ON or :SOURce:TRACe:REF:STATe 1
::SOURce:TRACe:REF:STATe?

:SOURce:TRACe:STORrefset / query

Saves the reference trace of normalization.

:SOURce:TRACe:STORref

:STATus:OPERation:CONDition?query

Queries the condition register of the Operation Status Register. The query returns the condition register as an integer.

integer - The condition register of the Operation Status Register.

:STATus:OPERation:ENABleset / query

Sets the enable register of the Operation Status Register. The query form returns the enable register in integer.

Name	Type	Values	Description
integer	integer	0 - 32767	Enable register value for the Operation Status Register.

:STATus:OPERation[:EVENt]?query

Queries the event register of the Operation Status Register.

integer - The event register of the Operation Status Register.

:STATus:PRESetset / query

Clears the enable register of the Operation Status Register and Questionable Status Register.

:STATus:QUEStionable:CONDition?query

Queries the condition register of the Questionable Status Register.

integer - The condition register of the Questionable Status Register.

:STATus:QUEStionable:ENABleset / query

Sets or queries the enable register of the Questionable Status Register.

Name	Type	Values	Description
integer	integer	-	Enable-register value to set.

integer - The query returns the enable register of the Questionable Status Register.

:STATus:QUEStionable[:EVENt]?query

Queries the event register of the Questionable Status Register.

integer - Returns the event register of the Questionable Status Register as an integer.

:SYSTem:BEEPer:STATeset / query

Turns on or off the beeper. Queries the status of the beeper.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Beeper state to set.

enum - The query returns 0 or 1.

*?

:SYSTem:COMMunicate:LAN[:SELF]:APPLyset / query

Applies the LAN interface parameter settings.

:SYSTem:COMMunicate:LAN[:SELF]:AUToip:STATeset / query

Enables or disables the auto IP setting mode. Queries the status of the auto IP setting mode.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns auto IP mode on or off.

enum - The query returns 0 or 1.

:SYSTem:COMMunicate:LAN[:SELF]:AUToip:STATe OFF|ON|0|1
:SYSTem:COMMunicate:LAN[:SELF]:AUToip:STATe?

:SYSTem:COMMunicate:LAN[:SELF]:DHCP:STATeset / query

Enables or disables the DHCP configuration mode. The query returns the current status of the DHCP configuration mode.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the DHCP configuration mode.

enum - Returns 0 or 1 indicating the DHCP configuration mode status.

:SYSTem:COMMunicate:LAN:SELF:DHCP:STATe ON
:SYSTem:COMMunicate:LAN:SELF:DHCP:STATe 1
:SYSTem:COMMunicate:LAN:SELF:DHCP:STATe?

:SYSTem:COMMunicate:LAN[:SELF]:IP:ADDRessset / query

Sets the IP address. Queries the IP address.

Name	Type	Values	Description
ip_address	string	-	IP address to set.

string - Returns the IP address.

:SYSTem:COMMunicate:LAN[:SELF]:IP:DNS:AUTO[:STATe]set / query

Sets or queries the DNS auto mode for the LAN self IP configuration. This command is only valid in manual IP setting mode.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables automatic DNS mode.

enum - The query returns 0 or 1.

:SYSTem:COMMunicate:LAN:SELF:IP:DNS:AUTO:STATe ON
:SYSTem:COMMunicate:LAN:SELF:IP:DNS:AUTO:STATe 1
:SYSTem:COMMunicate:LAN:SELF:IP:DNS:AUTO:STATe?

:SYSTem:COMMunicate:LAN[:SELF]:IP:DNSBackset / query

Sets the backup address for the DNS.

Name	Type	Values	Description
ip_address	string	-	Backup DNS IP address.

:SYSTem:COMMunicate:LAN[:SELF]:IP:DNSPreferredset / query

Sets the preferred address for the DNS. Queries the currently preferred DNS address.

Name	Type	Values	Description
ip_address	string	-	Preferred DNS IP address in the format nnn.nnn.nnn.nnn.

string - The current preferred DNS address in the format nnn.nnn.nnn.nnn.

:SYSTem:COMMunicate:LAN[:SELF]:IP:DNSServerset / query

Sets or queries the preferred DNS address for the LAN self interface. This command is only valid in manual DNS setting mode.

Name	Type	Values	Description
ip_address	string	-	DNS address in the format nnn.nnn.nnn.nnn.

string - The current preferred DNS address in the format nnn.nnn.nnn.nnn.

I cannot provide examples because the request is malformed.

:SYSTem:COMMunicate:LAN[:SELF]:IP:GATewayset / query

Sets the default gateway and queries the current default gateway. Valid only in manual IP setting mode.

Name	Type	Values	Description
ip_address	string	-	Default gateway address in the format nnn.nnn.nnn.nnn.

string - Current default gateway in the format nnn.nnn.nnn.nnn.

:SYSTem:COMMunicate:LAN:SELF:IP:GATeway 172.16.3.1
:SYSTem:COMMunicate:LAN:SELF:IP:GATeway?

:SYSTem:COMMunicate:LAN[:SELF]:IP:SUBMaskset / query

Sets the subnet mask. This command is only valid in manual IP setting mode.

Name	Type	Values	Description
ip_address	string	-	Subnet mask in the format "nnn.nnn.nnn.nnn".

Note: no separate example line for SUBMask query is shown in the slice.
The following command sets the subnet mask to "255.255.255.0".
:SYSTem:COMMunicate:LAN:SELF:IP:SUBMask 255.255.255.0

:SYSTem:COMMunicate:LAN[:SELF]:MANuip:STATeset / query

Enables or disables the manual IP setting mode. Queries the status of the manual IP setting mode.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables manual IP setting mode.

:SYSTem:COMMunicate:LAN:SELF:MANuip:STATe ON
:SYSTem:COMMunicate:LAN:SELF:MANuip:STATe
:SYSTem:COMMunicate:LAN:SELF:MANuip:STATe?

:SYSTem:COMMunicate:LAN[:SELF]:MDNS:STATeset / query

Enables or disables the state of the network information sending. Queries the on/off status of the network information sending.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns network information sending on or off.

:SYSTem:COMMunicate:LAN[:SELF]:RESetset / query

Resets the LAN setting by enabling DHCP and disabling Auto IP and Manual IP.

:SYSTem:CONFigure:INFormation?query

Queries the system information of the spectrum analyzer. The system information includes the model, serial number, software and hardware version number, and firmware version number.

string - The system information, for example model, serial number, board versions, and firmware version number. For RSA3030E-TG/RSA3015E-TG, the query also returns TG Board information.

:SYSTem:DATEset / query

Sets or queries the system date.

Name	Type	Values	Description
year	integer	-	Year value.
month	integer	-	Month value.
day	integer	-	Day value.

string - Returns the system date.

:SYSTem:FSWitch[:STATe]set / query

Sets the front-panel power switch on or off. Queries whether the front-panel power switch is on or off.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the power switch on or off.

enum - Returns 0 or 1 indicating whether the front-panel power switch is turned on or off.

SYSTem:FSWitch:STATe OFF or :SYSTem:FSWitch:STATe 0
SYSTem:FSWitch:STATe?

:SYSTem:LANGuageset / query

Sets the language of the instrument.

Name	Type	Values	Description
language	enum	ENGLish \| CHINese	Language to select for the instrument.

:SYSTem:LKEYset / query

Installs and activates the specified option.

Name	Type	Values	Description
option info	string	-	Indicates the order number of the option.
license info	string	-	Indicates the serial number of the option.

:SYSTem:LKEY RSA3000E-PA@8AD12B8EBC5DF492D1D4289B7CBA5B6150BF6F5D752D645C36D74530B05F39B49C461B23A50D6C94A34E06782AC4380070B0D1A86BA84E02768391FFD70C2103

:SYSTem:OPTion:STATe?query

Queries whether an option is activated or not.

Name	Type	Values	Description
option name	string	-	Option name to check.

returns

:SYSTem:PON:TYPEset / query

Selects the setting type the instrument recalls at power-on. The query reports which setting type is recalled at power-on.

Name	Type	Values	Description
mode	enum	PRESet \| LAST	Setting type recalled at power-on.

enum - Returns the setting type recalled at power-on.

SYSTem:PON:TYPE LAST
SYSTem:PON:TYPE?

:SYSTem:PRESetset / query

Recalls the system's preset settings and restores the system to the state specified by the :SYSTem:PRESet:TYPE command.

:SYSTem:PRESet:SAVEset / query

Saves the current system preset to one of the user preset locations.

Name	Type	Values	Description
preset	enum	USER1 \| USER2 \| USER3 \| USER4 \| USER5 \| USER6	User preset location to store the current system preset.

:SYSTem:PRESet:TYPEset / query

Selects the preset type of the system to FACTory or one of the user presets USER1 through USER6. The query returns the current preset type.

Name	Type	Values	Description
type	enum	FACTory \| USER1 \| USER2 \| USER3 \| USER4 \| USER5 \| USER6	Preset type to select.

enum - Returns the current preset type as FACT, USER1, USER2, USER3, USER4, USER5, or USER6.

not available

:SYSTem:PRESet:USER:SAVEset / query

Saves the current user setting. If the current preset type is FACTory, the setting is saved to User1; otherwise it is saved to the specified user setting.

:SYSTem:SCPI:DISPlayset / query

Sets or queries whether SCPI messages are displayed. The command accepts OFF/ON or 0/1 as the setting.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Controls SCPI message display.

:SYSTem:SCPI:DISPlay OFF|ON|0|1
:SYSTem:SCPI:DISPlay?

:SYSTem:SECurity:CLEarset / query

Clears all the data that you set safely. It deletes saved files, configuration files, and executes the factory resetting operation.

:SYSTem:SHOWset / query

Displays system-related information or turns that display off. The query returns the current system-information display setting.

Name	Type	Values	Description
mode	enum	OFF \| SYSTem \| OPTion \| LICense	Selects which system-related information to display.

enum - Returns the current SCPI system-information display setting.

:SYSTem:TIMEset / query

Sets or queries the instrument system time.

Name	Type	Values
hour	string	00 - 23
minute	string	00 - 59
second	string	00 - 59

string - The current system time in the format "HH,MM,SS".

:SYSTem:TIME 15,10,30
:SYSTem:TIME?

:TRIGger[:SEQuence]:ATRiggerset / query

Sets the auto trigger time. The command is only valid when the auto triggering function is enabled.

Name	Type	Values	Description
time	real	1 ms - 100 s	Auto trigger time.

:TRIGger[:SEQuence]:ATRigger:STATeset / query

Enables or disables the auto trigger function. Queries the setting status of the auto trigger function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables auto trigger.

enum - Returns the setting status of auto trigger function as 1 or 0.

TRIGger:SEQuence:ATRigger:STATe ON or :TRIGger:SEQuence:ATRigger:STATe 1
TRIGger:SEQuence:ATRigger:STATe?

:TRIGger[:SEQuence]:EXTernal<n>:DELayset / query

Sets or queries the delay time for the specified external trigger. The parameter n selects External Trigger 1 or 2.

Name	Type	Values	Description
n	discrete	1 - 2	Selects the external trigger number.
time	real	0 μs - 500 ms	Delay time for the external trigger.

real (s) - The query returns the delay time in scientific notation.

:TRIGger:SEQuence:EXTernal<n>:DELay <time>
:TRIGger:SEQuence:EXTernal<n>:DELay?

:TRIGger[:SEQuence]:EXTernal<n>:DELay:STATeset / query

Enables or disables the external trigger delay function. Queries the status of the external trigger delay function.

Name	Type	Values	Description
n	discrete	1 - 2	Selects External Trigger 1 or External Trigger 2.
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the external trigger delay function.

integer - Returns 1 or 0.

:TRIGger:SEQuence:EXTernal1:DELay:STATe ON or :TRIGger:SEQuence:EXTernal1:DELay:STATe 1
:TRIGger:SEQuence:EXTernal1:DELay:STATe?

:TRIGger[:SEQuence]:EXTernal<n>:SLOPeset / query

Sets the trigger edge for the external trigger. Queries the trigger edge for the external trigger.

Name	Type	Values	Description
n	integer	1 - 2	External trigger number: 1 indicates External Trigger 1, and 2 indicates External Trigger 2.
slope	enum	POSitive \| NEGative	Selects the trigger edge polarity.

enum - Returns the trigger edge for the external trigger.

:TRIGger[:SEQuence]:FMT:APTRiggerset / query

Sets the number of times for acquisition after each effective trigger is completed. Queries the number of times for acquisition after each effective trigger is completed.

Name	Type	Values	Description
number	integer	1	Number of acquisitions after each effective trigger is completed.

integer - Returns the number of times for acquisition after each effective trigger is completed.

:TRIGger:SEQuence:FMT:APTRigger 1
:TRIGger:SEQuence:FMT:APTRigger?

:TRIGger[:SEQuence]:FMT:CRITeriaset / query

Sets the trigger criteria for FMT, and queries the current FMT trigger criteria. This command is only valid when FMT is selected as the trigger source.

Name	Type	Values	Description
mode	enum	ENTer \| LEAVe \| INSide \| OUTSide \| ELEave \| LENTer	Trigger criteria for FMT.

enum - The query returns ENT, LEAV, INS, OUTS, ELE, or LENT.

:TRIGger:SEQuence:FMT:CRITeria ENTer

:TRIGger[:SEQuence]:FMT:DELayset / query

Sets the FMT trigger delay time. The query form returns the current delay value.

Name	Type	Values	Description
time	real	-	Delay time.

real - Returns the current FMT trigger delay time.

:TRIGger[:SEQuence]:FMT:DELay:STATeset / query

Enables or disables the FMT trigger delay function. Queries the status of the FMT trigger delay function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the FMT trigger delay function.

enum - Returns 1 or 0 indicating the status of the FMT trigger delay function.

:TRIGger:SEQuence:FMT:DELay:STATe ON or :TRIGger:SEQuence:FMT:DELay:STATe 1
:TRIGger:SEQuence:FMT:DELay:STATe?

:TRIGger[:SEQuence]:FMT:MASKset / query

Sets the mask to be used for the current trigger, or queries the current trigger mask. This command is only valid when FMT is selected as the trigger source.

Name	Type	Values	Description
mask	enum	UPPer \| LOWer \| BOTH	Selects the trigger mask.

enum - Returns the current mask as UPP, LOW, or BOTH.

:TRIGger:SEQuence:FMT:MASK UPPer
:TRIGger:SEQuence:FMT:MASK?

:TRIGger[:SEQuence]:FMT:MASK:EDITset / query

Sets the mask type that is currently viewed/edited. Queries the mask type that is currently viewed/edited.

enum - Returns the current mask type as UPP or LOW.

:TRIGger:SEQuence:FMT:MASK:EDIT UPPer
:TRIGger:SEQuence:FMT:MASK:EDIT?

:TRIGger[:SEQuence]:FMT:MASK:RELative:AMPLitudeset / query

Sets whether the amplitudes of the mask points are coupled to the reference level of the instrument. The query returns 1 or 0.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables coupling of mask point amplitudes to the reference level.

enum - Returns 1 if the amplitudes of the mask points are coupled to the reference level, or 0 if not.

:TRIGger:SEQuence:FMT:MASK:RELative:AMPLitude ON
:TRIGger:SEQuence:FMT:MASK:RELative:AMPLitude 1
:TRIGger:SEQuence:FMT:MASK:RELative:AMPLitude?

:TRIGger[:SEQuence]:FMT:MASK:RELative:FREQuencyset / query

Sets whether the frequencies of the mask points are coupled to the center frequency of the instrument. Queries whether the frequencies of the mask points are coupled to the center frequency of the instrument.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables coupling of mask-point frequencies to the instrument center frequency.

integer - Returns 1 when coupling is enabled and 0 when it is disabled.

:TRIGger:SEQuence:FMT:MASK:RELative:FREQuency ON
:TRIGger:SEQuence:FMT:MASK:RELative:FREQuency 1
:TRIGger:SEQuence:FMT:MASK:RELative:FREQuency?

:TRIGger[:SEQuence]:FMT:MASK<n>:BUILdset / query

Creates a mask according to the RT trace data. It is only valid when FMT is selected as the trigger source.

Name	Type	Values	Description
n	discrete	1 - 2	Selects which mask is edited; 1 indicates the upper mask and 2 indicates the lower mask.

:TRIGger:SEQuence:FMT:MASK1:BUILd

:TRIGger[:SEQuence]:FMT:MASK<n>:DATAset / query

Edits the mask parameters. The query returns the mask parameters.

Name	Type	Values	Description
freq	real	-	Mask point frequency value.
ampl	real	-	Mask point amplitude value.

returns - Returns the mask parameters.

:TRIGger:SEQuence:FMT:MASK<n>:DATA <freq>,<ampl>{,<freq>, <ampl>}
:TRIGger:SEQuence:FMT:MASK<n>:DATA?

:TRIGger[:SEQuence]:FMT:MASK<n>:DELeteset / query

Deletes the specified mask. This command is only valid when FMT is selected as the trigger source.

Name	Type	Values	Description
n	integer	1 - 2	Selects which mask to delete: 1 for the upper mask, 2 for the lower mask.

:TRIGger[:SEQuence]:FMT:MASK<n>:NEWset / query

Clears the currently activated mask and creates a default new mask. This command is only valid when FMT is selected as the trigger source.

Name	Type	Values	Description
n	integer	1 - 2	Selects which mask is edited: 1 for the upper mask, 2 for the lower mask.

:TRIGger[:SEQuence]:HOLDoffset / query

Sets the trigger holdoff time, or queries the current trigger holdoff time. This command is only valid when the trigger holdoff function is enabled.

Name	Type	Values	Description
time	real	100 μs - 500 ms	Trigger holdoff time.

real (s) - Returns the trigger holdoff time in scientific notation.

:TRIGger[:SEQuence]:HOLDoff:STATeset / query

Turns on or off the trigger holdoff function. Queries the status of the trigger holdoff function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the trigger holdoff function on or off.

enum - The query returns 1 or 0.

:TRIGger:SEQuence:HOLDoff:STATe ON or :TRIGger:SEQuence:HOLDoff:STATe 1
:TRIGger:SEQuence:HOLDoff:STATe?

:TRIGger[:SEQuence]:SOURceset / query

Sets the trigger source. Queries the trigger source.

Name	Type	Values	Description
source	enum	EXTernal1 \| EXTernal2 \| IMMediate \| FMT \| POWer	Selects the trigger source.

enum - The query returns EXT1, EXT2, IMM, FMT, or POW.

:TRIGger:SEQuence:SOURce IMMediate
:TRIGger:SEQuence:SOURce?

:TRIGger[:SEQuence]:VIDeo:DELayset / query

Sets the delay time for the video trigger. Queries the delay time for the video trigger.

Name	Type	Values	Description
time	real	0 μs - 500 ms	Delay time for the video trigger.

:TRIGger[:SEQuence]:VIDeo:DELay:STATeset / query

Enables or disables the video trigger delay function. Queries the status of the video trigger delay function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the video trigger delay function.

enum - The query returns 1 or 0.

:TRIGger:SEQuence:VIDeo:DELay:STATe ON or :TRIGger:SEQuence:VIDeo:DELay:STATe 1
:TRIGger:SEQuence:VIDeo:DELay:STATe?

:TRIGger[:SEQuence]:VIDeo:LEVelset / query

Sets the trigger level of the video trigger. Queries the trigger level of the video trigger.

Name	Type	Values	Description
ampl	real	-140 dBm - 30 dBm	Consecutive real number specifying the video trigger level.

real (dBm) - The query returns the trigger level of the video trigger.

:TRIGger:SEQuence:VIDeo:LEVel <ampl>
:TRIGger:SEQuence:VIDeo:LEVel?

:TRIGger[:SEQuence]:VIDeo:SLOPeset / query

Sets the polarity of the video trigger. Queries the polarity of the video trigger.

Name	Type	Values	Description
polarity	enum	POSitive \| NEGative	Polarity of the video trigger.

enum - The query returns POS or NEG.

:TRIGger:SEQuence:VIDeo:SLOPe POSitive
:TRIGger:SEQuence:VIDeo:SLOPe?

:TRIGger[:SEQuence]:ATRiggerset / query

Sets the auto trigger time. The command is only valid when the auto triggering function is enabled.

Name	Type	Values	Description
time	real	1 ms - 100 s	Auto trigger time.

:TRIGger[:SEQuence]:ATRigger:STATeset / query

Enables or disables the auto trigger function. Queries the setting status of the auto trigger function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables auto trigger.

enum - Returns the setting status of auto trigger function as 1 or 0.

TRIGger:SEQuence:ATRigger:STATe ON or :TRIGger:SEQuence:ATRigger:STATe 1
TRIGger:SEQuence:ATRigger:STATe?

:TRIGger[:SEQuence]:EXTernal<n>:DELayset / query

Sets or queries the delay time for the specified external trigger. The parameter n selects External Trigger 1 or 2.

Name	Type	Values	Description
n	discrete	1 - 2	Selects the external trigger number.
time	real	0 μs - 500 ms	Delay time for the external trigger.

real (s) - The query returns the delay time in scientific notation.

:TRIGger:SEQuence:EXTernal<n>:DELay <time>
:TRIGger:SEQuence:EXTernal<n>:DELay?

:TRIGger[:SEQuence]:EXTernal<n>:DELay:STATeset / query

Enables or disables the external trigger delay function. Queries the status of the external trigger delay function.

Name	Type	Values	Description
n	discrete	1 - 2	Selects External Trigger 1 or External Trigger 2.
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the external trigger delay function.

integer - Returns 1 or 0.

:TRIGger:SEQuence:EXTernal1:DELay:STATe ON or :TRIGger:SEQuence:EXTernal1:DELay:STATe 1
:TRIGger:SEQuence:EXTernal1:DELay:STATe?

:TRIGger[:SEQuence]:EXTernal<n>:SLOPeset / query

Sets the trigger edge for the external trigger. Queries the trigger edge for the external trigger.

Name	Type	Values	Description
n	integer	1 - 2	External trigger number: 1 indicates External Trigger 1, and 2 indicates External Trigger 2.
slope	enum	POSitive \| NEGative	Selects the trigger edge polarity.

enum - Returns the trigger edge for the external trigger.

:TRIGger[:SEQuence]:HOLDoffset / query

Sets the trigger holdoff time, or queries the current trigger holdoff time. This command is only valid when the trigger holdoff function is enabled.

Name	Type	Values	Description
time	real	100 μs - 500 ms	Trigger holdoff time.

real (s) - Returns the trigger holdoff time in scientific notation.

:TRIGger[:SEQuence]:HOLDoff:STATeset / query

Turns on or off the trigger holdoff function. Queries the status of the trigger holdoff function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the trigger holdoff function on or off.

enum - The query returns 1 or 0.

:TRIGger:SEQuence:HOLDoff:STATe ON or :TRIGger:SEQuence:HOLDoff:STATe 1
:TRIGger:SEQuence:HOLDoff:STATe?

:TRIGger[:SEQuence]:SOURceset / query

Sets the trigger source. Queries the trigger source.

Name	Type	Values	Description
source	enum	EXTernal1 \| EXTernal2 \| IMMediate \| FMT \| POWer	Selects the trigger source.

enum - The query returns EXT1, EXT2, IMM, FMT, or POW.

:TRIGger:SEQuence:SOURce IMMediate
:TRIGger:SEQuence:SOURce?

:TRIGger[:SEQuence]:ATRiggerset / query

Sets the auto trigger time. The command is only valid when the auto triggering function is enabled.

Name	Type	Values	Description
time	real	1 ms - 100 s	Auto trigger time.

:TRIGger[:SEQuence]:ATRigger:STATeset / query

Enables or disables the auto trigger function. Queries the setting status of the auto trigger function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables auto trigger.

enum - Returns the setting status of auto trigger function as 1 or 0.

TRIGger:SEQuence:ATRigger:STATe ON or :TRIGger:SEQuence:ATRigger:STATe 1
TRIGger:SEQuence:ATRigger:STATe?

:TRIGger[:SEQuence]:EXTernal<n>:DELayset / query

Sets or queries the delay time for the specified external trigger. The parameter n selects External Trigger 1 or 2.

Name	Type	Values	Description
n	discrete	1 - 2	Selects the external trigger number.
time	real	0 μs - 500 ms	Delay time for the external trigger.

real (s) - The query returns the delay time in scientific notation.

:TRIGger:SEQuence:EXTernal<n>:DELay <time>
:TRIGger:SEQuence:EXTernal<n>:DELay?

:TRIGger[:SEQuence]:EXTernal<n>:DELay:STATeset / query

Enables or disables the external trigger delay function. Queries the status of the external trigger delay function.

Name	Type	Values	Description
n	discrete	1 - 2	Selects External Trigger 1 or External Trigger 2.
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the external trigger delay function.

integer - Returns 1 or 0.

:TRIGger:SEQuence:EXTernal1:DELay:STATe ON or :TRIGger:SEQuence:EXTernal1:DELay:STATe 1
:TRIGger:SEQuence:EXTernal1:DELay:STATe?

:TRIGger[:SEQuence]:EXTernal<n>:SLOPeset / query

Sets the trigger edge for the external trigger. Queries the trigger edge for the external trigger.

Name	Type	Values	Description
n	integer	1 - 2	External trigger number: 1 indicates External Trigger 1, and 2 indicates External Trigger 2.
slope	enum	POSitive \| NEGative	Selects the trigger edge polarity.

enum - Returns the trigger edge for the external trigger.

:TRIGger[:SEQuence]:FMT:CRITeriaset / query

Sets the trigger criteria for FMT, and queries the current FMT trigger criteria. This command is only valid when FMT is selected as the trigger source.

Name	Type	Values	Description
mode	enum	ENTer \| LEAVe \| INSide \| OUTSide \| ELEave \| LENTer	Trigger criteria for FMT.

enum - The query returns ENT, LEAV, INS, OUTS, ELE, or LENT.

:TRIGger:SEQuence:FMT:CRITeria ENTer

:TRIGger[:SEQuence]:FMT:DELayset / query

Sets the FMT trigger delay time. The query form returns the current delay value.

Name	Type	Values	Description
time	real	-	Delay time.

real - Returns the current FMT trigger delay time.

:TRIGger[:SEQuence]:FMT:DELay:STATeset / query

Enables or disables the FMT trigger delay function. Queries the status of the FMT trigger delay function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables the FMT trigger delay function.

enum - Returns 1 or 0 indicating the status of the FMT trigger delay function.

:TRIGger:SEQuence:FMT:DELay:STATe ON or :TRIGger:SEQuence:FMT:DELay:STATe 1
:TRIGger:SEQuence:FMT:DELay:STATe?

:TRIGger[:SEQuence]:FMT:MASKset / query

Sets the mask to be used for the current trigger, or queries the current trigger mask. This command is only valid when FMT is selected as the trigger source.

Name	Type	Values	Description
mask	enum	UPPer \| LOWer \| BOTH	Selects the trigger mask.

enum - Returns the current mask as UPP, LOW, or BOTH.

:TRIGger:SEQuence:FMT:MASK UPPer
:TRIGger:SEQuence:FMT:MASK?

:TRIGger[:SEQuence]:FMT:MASK:EDITset / query

Sets the mask type that is currently viewed/edited. Queries the mask type that is currently viewed/edited.

enum - Returns the current mask type as UPP or LOW.

:TRIGger:SEQuence:FMT:MASK:EDIT UPPer
:TRIGger:SEQuence:FMT:MASK:EDIT?

:TRIGger[:SEQuence]:FMT:MASK:RELative:AMPLitudeset / query

Sets whether the amplitudes of the mask points are coupled to the reference level of the instrument. The query returns 1 or 0.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables coupling of mask point amplitudes to the reference level.

enum - Returns 1 if the amplitudes of the mask points are coupled to the reference level, or 0 if not.

:TRIGger:SEQuence:FMT:MASK:RELative:AMPLitude ON
:TRIGger:SEQuence:FMT:MASK:RELative:AMPLitude 1
:TRIGger:SEQuence:FMT:MASK:RELative:AMPLitude?

:TRIGger[:SEQuence]:FMT:MASK:RELative:FREQuencyset / query

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Enables or disables coupling of mask-point frequencies to the instrument center frequency.

integer - Returns 1 when coupling is enabled and 0 when it is disabled.

:TRIGger:SEQuence:FMT:MASK:RELative:FREQuency ON
:TRIGger:SEQuence:FMT:MASK:RELative:FREQuency 1
:TRIGger:SEQuence:FMT:MASK:RELative:FREQuency?

:TRIGger[:SEQuence]:FMT:MASK<n>:BUILdset / query

Creates a mask according to the RT trace data. It is only valid when FMT is selected as the trigger source.

Name	Type	Values	Description
n	discrete	1 - 2	Selects which mask is edited; 1 indicates the upper mask and 2 indicates the lower mask.

:TRIGger:SEQuence:FMT:MASK1:BUILd

:TRIGger[:SEQuence]:FMT:MASK<n>:DATAset / query

Edits the mask parameters. The query returns the mask parameters.

Name	Type	Values	Description
freq	real	-	Mask point frequency value.
ampl	real	-	Mask point amplitude value.

returns - Returns the mask parameters.

:TRIGger:SEQuence:FMT:MASK<n>:DATA <freq>,<ampl>{,<freq>, <ampl>}
:TRIGger:SEQuence:FMT:MASK<n>:DATA?

:TRIGger[:SEQuence]:FMT:MASK<n>:DELeteset / query

Deletes the specified mask. This command is only valid when FMT is selected as the trigger source.

Name	Type	Values	Description
n	integer	1 - 2	Selects which mask to delete: 1 for the upper mask, 2 for the lower mask.

:TRIGger[:SEQuence]:FMT:MASK<n>:NAMEset / query

Saves the FMT file with a specified filename suffixed with ".csv" to the default path (/"mode name"/mask). Queries the currently saved FMT filename.

Name	Type	Values	Description
n	discrete	-
string	string	-	Filename to save, without the ".csv" suffix.

string - The currently saved FMT filename.

:TRIGger:SEQuence:FMT:MASK1:DATA –80000000, –50, 80000000, –50
:TRIGger:SEQuence:FMT:MASK1:DATA?

:TRIGger[:SEQuence]:FMT:MASK<n>:NEWset / query

Clears the currently activated mask and creates a default new mask. This command is only valid when FMT is selected as the trigger source.

Name	Type	Values	Description
n	integer	1 - 2	Selects which mask is edited: 1 for the upper mask, 2 for the lower mask.

:TRIGger[:SEQuence]:HOLDoffset / query

Sets the trigger holdoff time, or queries the current trigger holdoff time. This command is only valid when the trigger holdoff function is enabled.

Name	Type	Values	Description
time	real	100 μs - 500 ms	Trigger holdoff time.

real (s) - Returns the trigger holdoff time in scientific notation.

:TRIGger[:SEQuence]:HOLDoff:STATeset / query

Turns on or off the trigger holdoff function. Queries the status of the trigger holdoff function.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Turns the trigger holdoff function on or off.

enum - The query returns 1 or 0.

:TRIGger:SEQuence:HOLDoff:STATe ON or :TRIGger:SEQuence:HOLDoff:STATe 1
:TRIGger:SEQuence:HOLDoff:STATe?

:TRIGger[:SEQuence]:LEVelset / query

Sets the trigger level of the IF power trigger. Queries the trigger level of the IF power trigger.

Name	Type	Values	Description
ampl	real	-140 - 30	Consecutive real number specifying the trigger level.

real - The query returns the trigger level in scientific notation.

:TRIGger:SEQuence:LEVel 10
:TRIGger:SEQuence:LEVel?

:TRIGger[:SEQuence]:SOURceset / query

Sets the trigger source. Queries the trigger source.

Name	Type	Values	Description
source	enum	EXTernal1 \| EXTernal2 \| IMMediate \| FMT \| POWer	Selects the trigger source.

enum - The query returns EXT1, EXT2, IMM, FMT, or POW.

:TRIGger:SEQuence:SOURce IMMediate
:TRIGger:SEQuence:SOURce?

:TRIGger2:MODEset / query

Sets the interface type of External Trigger 2. Queries the interface type of External Trigger 2.

Name	Type	Values	Description
mode	enum	IN \| OUT \| 0 \| 1	Selects whether External Trigger 2 uses the input or output interface.

enum - The query returns 0 or 1.

:TRIGger2:MODE IN
:TRIGger2:MODE?

:TRIGger2:MODEset / query

Sets the interface type of External Trigger 2. Queries the interface type of External Trigger 2.

Name	Type	Values	Description
mode	enum	IN \| OUT \| 0 \| 1	Selects whether External Trigger 2 uses the input or output interface.

enum - The query returns 0 or 1.

:TRIGger2:MODE IN
:TRIGger2:MODE?

:TRIGger2:MODEset / query

Sets the interface type of External Trigger 2. Queries the interface type of External Trigger 2.

Name	Type	Values	Description
mode	enum	IN \| OUT \| 0 \| 1	Selects whether External Trigger 2 uses the input or output interface.

enum - The query returns 0 or 1.

:TRIGger2:MODE IN
:TRIGger2:MODE?

:UNIT:POWerset / query

Sets the unit of the Y axis. Queries the unit of the Y axis.

Name	Type	Values	Description
unit	enum	DBM \| DBMV \| DBUV \| V \| W	Unit of the Y axis.

enum - The query returns DBM, DBMV, DBUV, V, or W.

:UNIT:POWer W
:UNIT:POWer?

:UNIT:POWerset / query

Sets the unit of the Y axis. Queries the unit of the Y axis.

Name	Type	Values	Description
unit	enum	DBM \| DBMV \| DBUV \| V \| W	Unit of the Y axis.

enum - The query returns DBM, DBMV, DBUV, V, or W.

:UNIT:POWer W
:UNIT:POWer?

:INITiate1:CONTinuousset / query

Sets the measurement mode of the meter to Continuous or Single. The query returns the current measurement mode.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Continuous mode ON\|1 or Single mode OFF\|0.

:INITiate2:CONTinuousset / query

Selects continuous (ON|1) or single (OFF|0) sweep mode. Queries the current sweep mode.

Name	Type	Values	Description
state	enum	OFF \| ON \| 0 \| 1	Sets the sweep mode to continuous or single.

enum - Returns the current sweep mode as 0 or 1.

:INITiate2:CONTinuous ON or :INITiate:CONTinuous 1
:INITiate2:CONTinuous?

:INITiate2:IMMediateset / query

Starts the scan, search, or the final measurement based on the selected scan sequence.

:INITiate2:RESTartset / query

Starts the scan, search, or the final measurement based on the selected scan sequence.

Products

Industries

Company

Blog

Rigol RSA3015E-TG

Rigol RSA3015E-TG

All commands

▶CALCulate155

▶TRACe17

▶CALibration6

▶CONFigure22

▶COUPle2

▶DISPlay65

▶FETCh23

▶FORMat6

▶*13

▶INITiate7

▶INSTrument12

▶MMEMory43

▶OUTPut1

▶READ20

▶TRACe<n>8

▶INPut3

▶SOURce4

▶STATus7

▶SYSTem29

▶TRIGger53

▶TRIGger23

▶UNIT2

▶INITiate11

▶INITiate23