Products

Industries

Blog

Contact

Book a demo

Equipment

Rohde & Schwarz

Rohde & Schwarz ROHDE-SCHWARZ-NGM202

SCPI COMMAND REFERENCE

Rohde & Schwarz ROHDE-SCHWARZ-NGM202

The Rohde & Schwarz ROHDE-SCHWARZ-NGM202 is Rohde & Schwarz's power supply in the NGM200 family. Its SCPI remote-control interface exposes 291 commands across 26 subsystems - 183 settable and 108 queries - and every command is documented here with its parameters, accepted values, return format, and a copy-paste PyVISA example for automating test and measurement.

291

Commands

183

Settable

108

Queries

Subsystems

SCPI

Verified

2026-07-16

All commands

:DIO:OUTPut[:STATe]set / query

Sets the state of the digital output pins OUT1 and OUT2 directly by SCPI command. The manual notes this command is used to configure the digital output / trigger-out parameter.

Name	Type	Values	Description
stateopt	enum	On \| Off	Enables or disables the selected digital output state.

:DIO:FAULt:CHANnelset / query

Sets or queries channel selection for the digital output fault source.

Name	Type	Values	Description
arg0	-	-

:DIO:FAULt:SOURceset / query

Sets or queries the operation mode used as the digital output fault source. If OUTPut is selected, the fault output is active when the selected channel output is off.

Name	Type	Values	Description
mode	enum	CC \| CV \| CR \| SINK \| PROTection \| OUTPut	Operation mode used as the digital output fault source.

enum - Returns the current operation mode of the digital output fault source.

DIO:FAUL:SOUR PROT

:DIO:FAULt:SOURce?query

Sets or queries the operation mode of the digital output fault source. If OUTPut is selected, the fault output is active when the selected channel output is off.

enum - Returns the current operation mode of the digital output fault source.

:DIO:FAULt[:STATe]set / query

Sets or queries the digital output fault state.

Name	Type	Values	Description
state	enum	1 \| 0	Enables or disables digital output fault.

enum - Returns the digital output fault state.

DIO:FAUL 1

:DIO:FAULt[:STATe]?query

Sets or queries the digital output fault. The command enables or disables the digital output fault state.

enum - Returns whether the digital output fault is enabled or disabled.

:DIO:FAULt:SIGNalset / query

Selects the digital output fault signal type.

Name	Type	Values	Description
arg0	enum	CONStant \| PULSe	Digital output fault signal type.

:DIO:OUTPut:SOURceset / query

Sets or queries the digital output source. The selected channel can use its output, external trigger, or be forced high.

Name	Type	Values	Description
arg0	integer	1 - 2	Channel selection for the digital output source.
arg1	enum	OUTPut \| TRIGger \| FORCed	Selects the digital output source mode.

enum - Returns the digital output source setting for the specified channel.

DIO:OUTP:SOUR 1, OUTP
DIO:OUTPut 1,0
DIO:OUTPut:SOURce 1,FORC
DIO:OUTPut 1,1

:DIO:OUTPut:SOURce?query

Sets or queries the digital output source. The source can be selected per channel and may be Output, Trigger, or Forced.

Name	Type	Values	Description
arg0	integer	1 - 2	Channel selection for the digital output source.
arg1	enum	OUTPut \| TRIGger \| FORCed	Digital output source to use.

enum - Returns the digital output source for the selected channel.

DIO:OUTP:SOUR 1, OUTP
DIO:OUTPut 1,0
DIO:OUTPut:SOURce 1,FORC
DIO:OUTPut 1,1

:DIO:OUTPut[:STATe]?query

Sets or queries the digital output channel selection. The state parameter enables or disables the digital output state.

Name	Type	Values	Description
arg0	integer	1 - 2	Channel selection for the digital output channel.
arg1	integer	0 - 1	Enables or disables the digital output state.

:DIO:OUTPut:SIGNalset / query

Selects the digital output signal type for a specified channel. For queries, returns the signal type at the digital output for the channel.

Name	Type	Values	Description
arg0	integer	1 - 2	Channel number.
arg1	enum	CONStant \| PULSe	Digital output signal type: constant level trigger signal or 100 ms pulse trigger signal.

enum - Signal type at the digital output for the specified channel.

DIO:OUTP:SIGN? 1

:DIO:OUTPut:SIGNal?query

Selects the digital output signal type for a specified channel. The query returns the signal type at the digital output for the given channel.

Name	Type	Values	Description
arg0	integer	1 - 2	Channel number.

enum - Returns the digital output signal type for the specified channel.

DIO:OUTP:SIGN? 1

:SYSTem:COMMunicate:LAN:HOSTnameset / query

Sets or shows the hostname assigned to the instrument for identification in the network.

Name	Type	Values	Description
hostname	string	-	Hostname assigned to the instrument.

:SYSTem:COMMunicate:LAN:SCPI:RAWPortset / query

Sets the SCPI Raw Port used to open a raw TCP/IP connection for sending raw SCPI commands to the instrument.

Name	Type	Values	Description
port	integer	0 - 65535	Port number for the raw TCP/IP SCPI connection.

:SYSTem:COMMunicate:LAN:DHCPset / query

Enables or disables DHCP for automatic network parameter distribution on the LAN connection. When ON, the instrument obtains address information automatically; when OFF, the addresses must be set manually.

Name	Type	Values	Description
state	enum	ON \| OFF	Sets the DHCP mode.

:SYSTem:COMMunicate:LAN:GATewayset / query

Sets the Gateway IP address used for LAN configuration. The slice shows it as one of the IP dialog fields together with IP Address and Subnet Mask.

:SYSTem:COMMunicate:LAN:IPADdressset / query

Sets the instrument's IP address in the LAN configuration. The page slice shows this as part of the IP dialog for configuring IP Address, Subnet Mask, and Gateway, but does not provide SCPI syntax details or value range.

:SYSTem:COMMunicate:LAN:SMASkset / query

Configures the subnet mask for the LAN interface. The slice only shows the IP dialog workflow and does not document a command syntax or parameter details for this mnemonic.

:SYSTem:COMMunicate:WLAN:DISCset / query

Disconnects the instrument from the current wireless LAN connection. The manual states to use the Wireless LAN settings dialog and select "Disconnect" to disconnect.

:SYSTem:COMMunicate:WLAN:ENABleset / query

Enables wireless LAN connectivity on the instrument. When set to On, the instrument begins searching for available WiFi networks and the status changes to Searching.

Name	Type	Values	Description
state	enum	On \| Off	Turns WLAN connection on or off.

:SYSTem:COMMunicate:WLAN:SELectset / query

Selects a WLAN network to connect to. After enabling wireless LAN, the instrument searches for available WiFi networks and connects to the selected one.

Name	Type	Values	Description
network	string	-	The required WiFi network to select.

Select "Select Network" to connect the required WiFi network.

:SYSTem:COMMunicate:VNC:ENABleset / query

Enables or disables the VNC connection.

Name	Type	Values	Description
state	enum	ON \| OFF	Sets whether VNC is enabled.

:SYSTem:COMMunicate:VNC:PORTset / query

Sets the VNC port number used for remote connections. The port can only be changed when VNC is disabled.

Name	Type	Values	Description
port	integer	-	Desired VNC port number.

:SYSTem:COMMunicate:FTP:ENABleset / query

Enables or disables the FTP service. The FTP settings can only be changed if this is set to OFF.

Name	Type	Values	Description
state	enum	ON \| OFF	Turns the FTP service on or off.

:SYSTem:COMMunicate:FTP:PASSwordset / query

Sets the FTP login password used for remote file access on the instrument. The setting can only be changed if FTP is disabled.

Name	Type	Values	Description
password	string	-	User name and password for login access.

:SYSTem:COMMunicate:FTP:PORTset / query

Sets the FTP server port number. The setting can only be changed when FTP is disabled.

Name	Type	Values	Description
port	integer	1 - 65535	Port number for the FTP server.

:SYSTem:COMMunicate:FTP:USERset / query

Sets the FTP user name used for login access. The username is one of the FTP access settings and can only be changed when FTP is disabled.

Name	Type	Values	Description
user name	string	-	User name for FTP login access.

:SYSTem:COMMunicate:GPIB:ADDRessset / query

Sets or queries the GPIB address for remote control via the GPIB interface. The manual notes that the NGL-B105 or NGM-B105 option must be installed for GPIB remote command use.

:SYSTem:COMMunicate:USB:CLASsset / query

Sets the USB connection class for the instrument. A change between USB TMC and USB CDC requires a reboot to take effect.

Name	Type	Values	Description
class	enum	TMC \| CDC	USB class to select.

:SYSTem:LICense:ADDset / query

Adds a license key code manually through the license dialog. The manual also describes installing a license from an XML file on USB, but this command specifically invokes the on-screen keyboard for entering the key code.

:SYSTem:LICense:LOADset / query

Installs a license option from a file or by entering a registered license key code. The manual describes loading an XML license file from USB and also mentions manual key-code entry in the license dialog.

Name	Type	Values	Description
filename	string	-	License file to install from USB.

Select "Load File" to load the license file from the USB stick.

:SYSTem:LICense:REMoveset / query

Removes a previously installed license option using the entered 30-digit device key. The instrument confirms removal with a popup message if the key code is correct.

Name	Type	Values	Description
key code	string	-	30-digit number of the option to remove.

:SYSTem:BEEPer:CURRent:STATeset / query

Enables or disables beep sound for the "current control" alert.

Name	Type	Values	Description
arg0	integer	0 - 1	Enables or disables the "Current control" beep sound.

:SYSTem:BEEPer:PROTection:STATeset / query

Enables or disables the beep sound for "protection" alerts.

Name	Type	Values	Description
arg0	enum	1 \| 0	Enables or disables the protection beep sound.

SYST:BEEP:WARN:STAT ON

:SYSTem:BEEPer:PROTection[:IMMediate]set / query

Returns a single "protection" beep sound immediately.

:SYSTem:BEEPer:STATeset / query

Sets or queries the state of the front panel control beeper. A value of 1 activates the beeper and 0 deactivates it.

Name	Type	Values	Description
mode	enum	1 \| 0	Control beeper state.

enum - Returns the state of the front panel control beeper: 0 for deactivated (OFF) and 1 for activated (ON).

SYSTem:BEEPer:STATe 1
SYSTem:BEEPer:STATe?

:SYSTem:BEEPer:STATe?query

Queries the state of the front panel control beeper. Returns "0" for deactivated (OFF) and "1" for activated (ON) control beeper.

enum - Returns the front panel control beeper state.

SYSTem:BEEPer:STATe?

:SYSTem:BEEPer:WARNing:STATeset / query

Enables or disables beep sound for errors and warnings.

Name	Type	Values	Description
state	enum	ON \| OFF	Enables or disables the warning beep.

:SYSTem:BEEPer:WARNing[:IMMediate]set / query

Sends a single error or warning beep immediately.

SYSTem:BEEPer:WARNing[:IMMediate]

:SYSTem:BEEPer[:COMPlete]:STATeset / query

Enables or disables the operation-complete beep sound.

Name	Type	Values	Description
state	enum	ON \| OFF	Enables or disables the operation-complete beep sound.

SYST:BEEP:STAT ON

:SYSTem:BEEPer[:COMPlete][:IMMediate]set / query

Sent a single operation complete beep immediately.

:SYSTem:COMMunicate:LAN:ADDRessset / query

Sets or queries the IP address for LAN.

Name	Type	Values	Description
Ip address	string	-	String containing the IP address ('x.x.x.x').

SYST:COMM:LAN:ADDR '172.76.68.30'

:SYSTem:COMMunicate:LAN:APPLyset / query

Applies the current LAN settings to the instrument.

:SYSTem:COMMunicate:LAN:DGATewayset / query

Sets or queries the default gateway in the LAN.

Name	Type	Values	Description
gateway	string	-	String containing the identifier of the gateway.

:SYSTem:COMMunicate:LAN:DISCardset / query

Discards the pending LAN settings changes.

:SYSTem:COMMunicate:LAN:EDITed?query

Queries the edit mode of LAN settings.

boolean - Returns 1 if LAN settings are in edit mode and 0 if LAN settings are applied.

SYST:COMM:LAN:EDIT?

:SYSTem:COMMunicate:LAN:MAC?query

Queries the MAC address of the instrument.

string - Returns the MAC address.

SYST:COMM:LAN:MAC?

:SYSTem:COMMunicate:LAN:RESetset / query

Resets the instrument LAN settings.

:SYSTem:COMMunicate:NETWork:VNC:PORTset / query

Sets or queries the instrument VNC port number.

Name	Type	Values	Description
Port	integer	-	VNC port number.

integer - Returns instrument VNC port number.

SYST:COMM:NETW:VNC:PORT?

:SYSTem:COMMunicate:NETWork:VNC[:STATe]set / query

Enables or disables the VNC connection.

Name	Type	Values	Description
En-/Disable VNC	enum	ON \| OFF	Enables or disables the VNC connection.

:SYSTem:COMMunicate:NETWork:VNC ON

:SYSTem:DATEset / query

Sets or queries the system date.

Name	Type	Values	Description
year	integer	-	Sets year of the date.
month	integer	-	Sets month of the date.
day	integer	-	Sets day of the date.

string - Returns the system date.

SYSTem:DATE 2018, 10, 15
SYSTem:DATE? -> 2018, 10, 15

:SYSTem:KEY:BRIGhtnessset / query

Sets or queries the front panel key brightness.

Name	Type	Values	Description
front key brightness	real	0.0 - 1.0	Sets the key brightness.

real - Returns key brightness value.

SYSTem:KEY:BRIGhtness 1.0
SYSTem:KEY:BRIGhtness? -> 1.0

:SYSTem:LOCalset / query

Sets the system to front panel control. The front panel control is unlocked, and if it was locked with SYSTem:RWLock, the locked-panel message box on the instrument display disappears.

:SYSTem:REMoteset / query

Sets the system to remote state. The front panel control is locked; pressing the softkey button [*] activates front panel control.

:SYSTem:RESTartset / query

Restarts the instrument.

:SYSTem:RWLockset / query

Sets the system to remote state and locks the front panel control. A message box is shown on the instrument display; the front panel can only be unlocked via SYSTem:LOCal.

:SYSTem:SETTing:DEFault:SAVEset / query

Creates a settings file.

Name	Type	Values	Description
File pathopt	string	-	Directory path for the saved settings file.

:SYSTem:TIMEset / query

Sets or queries the system time.

Name	Type	Values	Description
hour	integer	-	Sets the hours of the system time.
minute	integer	-	Sets the minutes of the system time.
second	integer	-	Sets the seconds of the system time.

string - Returns system time.

SYSTem:TIME 12, 30, 59
SYSTem:TIME? -> 12, 30, 59

:SYSTem:UPTime?query

Queries the system uptime.

real - Returns the system uptime.

:SYSTem:ERRor[:NEXT]?query

Returns one entry from the error queue as a plain text error message. If no error messages are stored, the instrument responds with 0, "No error".

string - One error queue entry is returned on each call, or 0, "No error" if the queue is empty.

*CLSset / query

Clears the status byte (STB), standard event register (ESR), and the event bits of the questionable and operation registers. It does not change the mask or transition parts of the registers and clears the output buffer.

*ESEset / query

Sets the event status enable register to the specified value. The query returns the contents of the event status enable register in decimal form.

Name	Type	Values	Description
value	integer	0 - 255	Value written to the event status enable register.

*ESR?query

Returns the contents of the event status register in decimal form and then sets the register to zero.

integer - Contents of the event status register in decimal form; the register is then cleared to zero.

*IDN?query

Returns the instrument identification.

string - The instrument identification string in the form "Rohde&Schwarz,<device type>,<part number>/<serial number>,<firmware version>".

*OPCset / query

Sets bit 0 in the event status register when all preceding commands have been executed. The query variant writes a "1" into the output buffer when all preceding commands have been executed, for command synchronization.

*OPT?query

Queries the options included in the instrument.

string - Returns the options included in the instrument.

*SREset / query

Sets the service request enable register to the indicated value. It determines under which conditions a service request is triggered.

Name	Type	Values	Description
contents	integer	0 - 255	Contents of the service request enable register in decimal form. Bit 6 (MSS mask bit) is always 0.

*TRGset / query

Triggers all actions waiting for a trigger event. In particular, *TRG generates a manual trigger signal and complements the TRIGger subsystem.

*TST?query

Initiates self-tests of the instrument and returns an error code.

integer - Error code returned by the self-test query; 0 means no errors occurred, and a positive integer indicates an error occurred.

*WAIset / query

Prevents servicing of subsequent commands until all preceding commands have been executed and all signals have settled. It is a synchronization event command.

*OPC?query

Waits until all previous remote commands have been executed. This query is typically used for synchronization before continuing with subsequent commands.

boolean - Returns 1 when all previous commands have been completed.

*OPC?

*RSTset / query

Resets the instrument to its default state. It is used in the example before configuring FastLog.

*RST

*STB?query

Returns the status byte. The byte can be polled to check whether an operation status event is available.

integer - The status byte value.

*STB?

:DISPlay:BRIGhtnessset / query

Sets or queries the display brightness. The displayed value ranges from 0.0 to 1.0 in steps of 0.1.

Name	Type	Values	Description
brightness	real	0.0 - 1.0	Displays brightness for the instrument.

real - Returns the display brightness value.

DISPlay:BRIGhtness 0.5
DISPlay:BRIGhtness? -> 0.5

:DISPlay[:WINDow]:TEXT:CLEarset / query

Clears the text message box on the front display.

:DISPlay[:WINDow]:TEXT[:DATA]set / query

Displays a text message box on the front display. Setting only.

Name	Type	Values	Description
string	string	-	Text message for display.

DISPlay:TEXT "Instrument Test"

:TRIGger[:SEQuence][:IMMediate]:SOURceset / query

Sets or queries the trigger source.

Name	Type	Values	Description
arg0	enum	OUTPut \| OMODe \| DIO	Trigger source selection.

enum - Returns the selected trigger source.

TRIG:SOUR OMOD

:TRIGger[:SEQuence][:IMMediate]:SOURce?query

Queries the trigger source used by the trigger system. The source can be selected from output channel, operation modes, or DIO connector.

enum - Returns the selected trigger source.

TRIG:SOUR OMOD

:TRIGger[:STATe]set / query

Enables or disables the trigger system. When enabled, the selected trigger source becomes active upon being triggered.

Name	Type	Values	Description
arg0	enum	1 \| 0	Enables or disables the trigger system.

:TRIGger[:SEQuence][:IMMediate]:SOURce:DIO:CHANnelset / query

Sets or queries the device channel for trigger source "Digital In Channel". This setting is only available if DIO pin is set to "EXT".

Name	Type	Values	Description
arg0	enum	OUT1 \| OUTP1 \| OUTPut1 \| CH1 \| OUT2 \| OUTP2 \| OUTPut2 \| CH2 \| ANY	Device channel used for trigger source "Digital In Channel".

enum - Returns the selected device channel for trigger source "Digital In Channel".

TRIG:SOUR:DIO:CHAN 1

:TRIGger[:SEQuence][:IMMediate]:SOURce:DIO:CHANnel?query

Sets or queries the device channel for trigger source "Digital In Channel". This setting is only available if DIO pin is set to "EXT".

Name	Type	Values	Description
arg0	enum	OUT1 \| OUTP1 \| OUTPut1 \| CH1 \| OUT2 \| OUTP2 \| OUTPut2 \| CH2 \| ANY	Device channel to use for trigger source "Digital In Channel".

enum - Returns the selected device channel for trigger source "Digital In Channel".

TRIG:SOUR:DIO:CHAN 1

:TRIGger[:SEQuence][:IMMediate]:SOURce:DIO:PINset / query

Sets or queries the DIO pin to trigger on for trigger source "Digital In Channel". Pin 3 is monitored for IN, and pin 2 (Ch1) and pin 10 (Ch2) are monitored for EXT.

Name	Type	Values	Description
arg0	enum	IN \| EXT	DIO pin selection for trigger source "Digital In Channel".

TRIG:SOUR:DIO:PIN IN

:TRIGger[:SEQuence][:IMMediate]:SOURce:DIO:PIN?query

Sets or queries the DIO pin to trigger on for trigger source "Digital In Channel". This setting is only available if DIO pin is set to "EXT".

Name	Type	Values	Description
arg0	enum	IN \| EXT	DIO pin to monitor for trigger source "Digital In Channel".

TRIG:SOUR:DIO:PIN IN

:TRIGger[:SEQuence][:IMMediate]:SOURce:OMODeset / query

Sets or queries the operation mode used for trigger source "operation mode". The available modes are CC, CV, CR, SINK, and PROTection.

Name	Type	Values	Description
mode	enum	CC \| CV \| CR \| SINK \| PROTection	Operation mode to trigger on.

TRIG:SOUR:OMODe CC

:TRIGger[:SEQuence][:IMMediate]:SOURce:OMODe?query

Sets or queries the operation mode to trigger on for trigger source "operation mode".

Name	Type	Values	Description
mode	enum	CC \| CV \| CR \| SINK \| PROTection	Operation mode used as the trigger source setting.

:TRIGger[:SEQuence][:IMMediate]:SOURce:OMODe:CHANnelset / query

Sets or queries the device channel for trigger source "Operation Modes". The selected channel can be Ch1, Ch2, or any available channel meeting the trigger condition.

Name	Type	Values	Description
arg0	enum	OUT1 \| OUTP1 \| OUTPut1 \| CH1 \| OUT2 \| OUTP2 \| OUTPut2 \| CH2 \| ANY	Device channel for trigger source "Operation Modes".

enum - Returns the selected device channel for trigger source "Operation Modes".

TRIG:SOUR:OMOD:CHAN 1

:TRIGger[:SEQuence][:IMMediate]:SOURce:OMODe:CHANnel?query

Sets or queries the device channel for trigger source "Operation Modes". Ch1, Ch2, or any available channel meeting the trigger condition can be selected.

Name	Type	Values	Description
arg0	enum	OUT1 \| OUTP1 \| OUTPut1 \| CH1 \| OUT2 \| OUTP2 \| OUTPut2 \| CH2 \| ANY	Device channel for trigger source "Operation Modes".

enum - Returns the selected device channel for trigger source "Operation Modes".

TRIG:SOUR:OMOD:CHAN 1

:TRIGger[:SEQuence][:IMMediate]:SOURce:OUTPut:CHANnelset / query

Sets or queries the device channel for trigger source "Output".

Name	Type	Values	Description
arg0	enum	OUT1 \| OUTP1 \| OUTPut1 \| CH1 \| OUT2 \| OUTP2 \| OUTPut2 \| CH2 \| ANY	Device channel selected for trigger source "Output".

:TRIGger[:SEQuence][:IMMediate]:SOURce:OUTPut:CHANnel?query

Sets or queries the device channel for trigger source "Output". The available channel selections are OUT1/CH1, OUT2/CH2, or ANY.

Name	Type	Values	Description
arg0	enum	OUT1 \| OUTP1 \| OUTPut1 \| CH1 \| OUT2 \| OUTP2 \| OUTPut2 \| CH2 \| ANY	Device channel for trigger source "Output".

enum - Returns the selected device channel for trigger source "Output".

TRIG:SOUR:OUTP:CHAN 1

:INSTrument:NSELectset / query

Selects or queries the channel by number.

Name	Type	Values	Description
channel	integer	1 - 2	Channel number to select.

integer - Returns the number of the selected channel.

INST:NSEL 1
INST:NSEL?

:INSTrument:NSELect?query

Queries the selected channel by number. The response is the channel number 1 or 2.

integer - Returns the number of the selected channel.

:INSTrument[:SELect]set / query

Selects or queries the channel by keyword. The command accepts either the output keyword for channel 1 or 2, or the channel number via the related NSELect form.

Name	Type	Values	Description
channel	enum	OUT1 \| OUTP1 \| OUTPut1 \| CH1 \| OUT2 \| OUTP2 \| OUTPut2 \| CH2	Channel keyword to select channel 1 or channel 2.

INST:NSEL 1
INST?
INST:NSEL?

:INSTrument[:SELect]?query

Selects or queries the channel by keyword. The channel can be selected as OUT1/OUT2 or by the corresponding output/channel keyword variants.

Name	Type	Values	Description
channel	enum	OUT1 \| OUTP1 \| OUTPut1 \| CH1 \| OUT2 \| OUTP2 \| OUTPut2 \| CH2	Channel keyword to select.

enum - Returns the selected channel by keyword.

INST OUT1
INST?
INST:NSEL 1
INST:NSEL?

[SOURce:]ALIMit[:STATe]set / query

Sets or queries the safety limit state.

Name	Type	Values	Description
state	enum	1 \| 0	Activates or deactivates the safety limit.
channel listopt	channel_list	-	Channel list to set or query.

enum - Returns the safety limit state for the specified channel list.

ALIM 1, (@1)

[SOURce:]ALIMit[:STATe]?query

Sets or queries the safety limit state. For the setter, 1 activates the safety limit and 0 deactivates it.

Name	Type	Values	Description
state	enum	1 \| 0	Activates or deactivates the safety limit.
channel listopt	channel_list	-	Channel list to set or query.

enum - Returns the safety limit state for the specified channel list.

ALIM 1, (@1)

[SOURce:]VOLTage[:LEVel][:IMMediate]:ALIMit:LOWerset / query

Sets or queries the lower safety limit for voltage.

Name	Type	Values	Description
voltage	real	0.000E+00 - 20.050E+00	Numeric value for the safety limit; MINimum and MAXimum are also accepted.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum	Selects the minimum or maximum safety-limit value instead of a numeric value.

real - Returns the lower safety limit for voltage.

VOLT:ALIM:LOW? (@1)

[SOURce:]VOLTage[:LEVel][:IMMediate]:ALIMit:LOWer?query

Queries the lower safety limit for voltage. The query can be performed for a specified channel list.

Name	Type	Values	Description
channel listopt	channel_list	-	Channel list to query.

real (V) - Returns the lower safety limit for voltage.

VOLT:ALIM:LOW? (@1)

[SOURce:]VOLTage[:LEVel][:IMMediate]:ALIMit[:UPPer]set / query

Sets or queries the upper safety limit for voltage. The query returns the upper safety limit at the specified channel.

Name	Type	Values	Description
voltage	real	0.000E+00 - 20.050E+00	Numeric value for upper safety limit.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum	Selects the minimum or maximum allowed value instead of a numeric value.
channel listopt	channel_list	-	Channel list for setting and query.

real - Upper safety limit for voltage at the specified channel.

VOLT:ALIM:UPP? (@1)

[SOURce:]VOLTage[:LEVel][:IMMediate]:ALIMit[:UPPer]?query

Queries the upper safety limit for voltage. Channel selection is specified with a channel list.

Name	Type	Values	Description
channel listopt	channel_list	-	Channel list for the query.

real - Upper safety limit for voltage at the specified channel.

VOLT:ALIM:UPP? (@1)

[SOURce:]VOLTage[:LEVel][:IMMediate][:AMPLitude]set / query

Sets or queries the voltage value of the selected channel. The setting accepts a numeric value in volts, MIN/MAX keywords, or step commands UP/DOWN; the query can be applied to a channel list.

Name	Type	Values	Description
voltage	real	0.000 - 20.05	Voltage value to set in volts, or the keywords MIN/MAX, UP, or DOWN as documented.
channel listopt	channel_list	-	Channel list used with the query form.

VOLT? (@1)

[SOURce:]VOLTage[:LEVel][:IMMediate][:AMPLitude]?query

Sets or queries the voltage value of the selected channel. The setter accepts a numeric value in volts, MIN/MAX keywords, or UP/DOWN relative adjustments.

Name	Type	Values	Description
voltage	real	0.000 - 20.05	Voltage value to set, or the keywords MIN/MAX/UP/DOWN as documented.
channel listopt	channel_list	-	Channel list for querying the voltage of specific channels.

real (V) - Returns the voltage of the selected channel in volts.

VOLT? (@1)

[SOURce:]VOLTage:RANGeset / query

Sets or queries the range for target voltage. Refer to the datasheet for the measurement accuracy according to the measurement range selected.

Name	Type	Values	Description
arg0	-	-
Channel listopt	channel_list	-

returns

VOLT:RANG 20

[SOURce:]VOLTage:RANGe?query

Sets or queries the range for target voltage. Refer to the datasheet for the measurement accuracy according to the measurement range selected.

Name	Type	Values	Description
channel listopt	channel_list	-	Channel list.

VOLT:RANG 20

[SOURce:]VOLTage[:LEVel][:IMMediate]:STEP[:INCRement]set / query

Sets or queries the incremental step size for the VOLT UP | VOLT DOWN command.

Name	Type	Values	Description
stepsize	real	0.001 - 5.000	Step value in volts, or DEF \| DEFault for the default stepsize.
qualifieropt	enum	DEF \| DEFault	Queries the default voltage step size.

VOLT:STEP 0.001
VOLT:STEP DEF
VOLT:STEP? DEF -> 0.10

[SOURce:]VOLTage[:LEVel][:IMMediate]:STEP[:INCRement]?query

Sets or queries the incremental step size for the VOLT UP and VOLT DOWN command. The query can also request the default step size.

Name	Type	Values	Description
stepsize	real	0.001 - 5.000	Step value in volts; DEF or DEFault selects the default value.
qualifieropt	enum	DEF \| DEFault	Use DEF or DEFault with the setter/query to select or query the default stepsize.

real (V) - Returns the default stepsize voltage when queried with DEF or DEFault.

VOLT:STEP 0.001
VOLT:STEP DEF
VOLT:STEP? DEF -> 0.10

[SOURce:]VOLTage:DVM[:STATe]set / query

Sets or queries digital voltmeter measurements. The command enables or disables the DVM state for the specified channel list.

Name	Type	Values	Description
state	boolean	-	1 enables digital voltmeter measurement; 0 disables it.
channel listopt	channel_list	-	Channel list to apply the setting or query to.

boolean - Returns the DVM state, with 1 indicating enabled and 0 indicating disabled.

VOLT:DVM 1
MEAS:VOLT:DVM? -> 1.000E+00
VOLT:DVM? (@1)

[SOURce:]VOLTage:PROTection:CLEarset / query

Resets the OVP state of the selected channel. If an OVP event occurred before, the reset also erases the message on the display.

Name	Type	Values	Description
channel listopt	channel_list	-	Selected channel list.

VOLT:PROT:CLEAR (@1)

[SOURce:]VOLTage:PROTection:LEVelset / query

Sets the overvoltage protection value of the selected channel.

Name	Type	Values	Description
voltage	real	0.001 V	Numeric value for the overvoltage protection value.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum \| DEF \| DEFault	Alternative to a numeric voltage value.

SOUR:VOLT:PROT:LEV 5

[SOURce:]VOLTage:PROTection[:STATe]set / query

Sets or queries the OVP state of the previous selected channel.

Name	Type	Values	Description
state	enum	0 \| 1	OVP state to set: 0 deactivates OPP, 1 activates OPP.
channel listopt	channel_list	-	Channel list for setting and query.

VOLT:PROT? (@1)

[SOURce:]VOLTage:PROTection:TRIPped?query

Queries the OVP state of the selected channel.

Name	Type	Values	Description
listopt	channel_list	-	Channel list selecting the channel to query.

enum - Returns whether the overvoltage protection is tripped or not.

VOLT:PROT:TRIP?
VOLT:PROT:TRIP? (@1)

[SOURce:]VOLTage:RAMP[:STATe]set / query

Sets or queries the state of the ramp function for the previously selected channel. The query can optionally be limited to a specified channel list.

Name	Type	Values	Description
state	enum	0 \| 1	EasyRamp state; 0 deactivates the function and 1 activates it.
channel listopt	channel_list	-	Channel list to query.

INST OUT1
VOLT:RAMP ON
VOLT:RAMP? -> 1
VOLT:RAMP ON, (@1)
VOLT:RAMP? (@1)

[SOURce:]VOLTage:RAMP[:STATe]?query

Sets or queries the state of the ramp function for the selected output channel. The query can be applied to a specific channel list.

Name	Type	Values	Description
state	enum	0 \| 1 \| OFF \| ON	EasyRamp function state: deactivated or activated.
channel listopt	channel_list	-	Channel list to query.

enum - Returns the EasyRamp function state.

INST OUT1
VOLT:RAMP ON
VOLT:RAMP? -> 1
VOLT:RAMP ON, (@1)
VOLT:RAMP? (@1)

[SOURce:]VOLTage:RAMP:DURationset / query

Sets or queries the duration of the voltage ramp.

Name	Type	Values	Description
duration	real	0.01 - 10.00	Duration of the ramp function in seconds.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum \| DEF \| DEFault	Use MINimum for the minimum duration at 0.00 s, MAXimum for the minimum duration at 10 s, or DEFault for the default duration at 0.01 s.

real (s) - Returns the duration of the ramp function.

VOLT:RAMP:DUR 4
VOLT:RAMP:DUR? -> 4
VOLT:RAMP:DUR 4, (@1)
VOLT:RAMP:DUR? (@1)

[SOURce:]VOLTage:RAMP:DURation?query

Sets or queries the duration of the voltage ramp.

Name	Type	Values	Description
duration	real	0.01 - 10.00	Duration of the ramp function in seconds.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum \| DEF \| DEFault	Sets the duration to the minimum, maximum, or default value.
channel listopt	channel_list	-	Channel list for setting or querying a specific channel.

VOLT:RAMP:DUR 4
VOLT:RAMP:DUR? -> 4
VOLT:RAMP:DUR 4, (@1)
VOLT:RAMP:DUR? (@1)

[SOURce:]CURRent[:LEVel][:IMMediate]:ALIMit:LOWerset / query

Sets or queries the lower safety limit for current. For up to 6 V, the allowed range is 0.001 to 3.010; above 6 V, the allowed range is 0.001 to 6.010.

Name	Type	Values	Description
current	real	0.001E+00 - 3.010E+00	Numeric value for lower safety limit.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum	Sets the lower safety limit to the minimum or maximum allowed value.
list	channel_list	-	Channel list.

CURR:ALIM:LOW? (@1)

[SOURce:]CURRent[:LEVel][:IMMediate]:ALIMit:LOWer?query

Queries the lower safety limit for current. The query takes an optional channel list and returns the configured lower current safety limit for the specified channel(s).

Name	Type	Values	Description
channel listopt	channel_list	-	Channel list to query.

real - Lower safety limit for current.

CURR:ALIM:LOW? (@1)

[SOURce:]CURRent[:LEVel][:IMMediate]:ALIMit[:UPPer]set / query

Sets or queries the upper safety limit for current on the specified channel. The numeric value is constrained by the output voltage range and has a 0.001 increment.

Name	Type	Values	Description
value	real	0.001E+00 - 3.010E+00	Numeric value for the upper safety limit.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum	Selects the minimum or maximum allowed upper safety limit.
channel_list	channel_list	-	Channel list identifying the output channel(s).

real (A) - Returns the upper safety limit for current for the specified channel.

CURR:ALIM:UPP? (@1)

[SOURce:]CURRent[:LEVel][:IMMediate]:ALIMit[:UPPer]?query

Queries the upper safety limit for current at the selected channel. The query accepts a channel list parameter.

Name	Type	Values	Description
channel list	channel_list	-	Channel or channels to query.

real (A) - Upper safety limit for current at the selected channel.

CURR:ALIM:UPP? (@1)

[SOURce:]CURRent[:LEVel][:IMMediate]:STEP[:INCRement]set / query

Sets or queries the incremental step size for the CURR UP and CURR DOWN commands.

Name	Type	Values	Description
stepsize	real	0.0001 - 2.000	Step value in amperes, or DEF/DEFault for the default stepsize.
qualifieropt	enum	DEF \| DEFault	Optional query qualifier that requests the default step size.

real (A) - Returns the incremental step size, or the default step size when queried with DEF or DEFault.

CURR:STEP 0.005
CURR:STEP DEF
VOLT:STEP? DEF -> 0.1000E+00

[SOURce:]CURRent[:LEVel][:IMMediate][:AMPLitude]set / query

Sets or queries the current value of the selected channel.

Name	Type	Values	Description
current	real	0.000 - 6.010	Numeric current value for the selected channel.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum \| UP \| DOWN	Special keyword for minimum, maximum, step up, or step down behavior.

[SOURce:]CURRent:RANGeset / query

Sets or queries the current range for the target current. Refer to the datasheet for the measurement accuracy according to the selected measurement range.

Name	Type	Values	Description
arg0	real	MINimum - MAXimum	Current measurement range to set.
channel listopt	channel_list	-	Channel list to apply the command to.

real (A) - Current measurement range of the specified channel.

CURR:RANG 10
CURR? (@1)

[SOURce:]CURRent:PROTection:CLEarset / query

Resets the OCP state of the selected channel. If an OCP event has occurred before, the reset also erases the message on the display.

Name	Type	Values	Description
channel listopt	channel_list	-	Selected channel list.

CURR:PROT:CLE (@1)

[SOURce:]CURRent:PROTection:DELay:INITialset / query

Sets or queries the initial fuse delay time once output turns on.

Name	Type	Values	Description
duration	real	0.00 - 60.00	Numeric value for initial fuse delay.

[SOURce:]CURRent:PROTection:DELay:INITial <duration>
[SOURce:]CURRent:PROTection:DELay:INITial? [<Channel list>]

[SOURce:]CURRent:PROTection:DELayset / query

Sets or queries the fuse delay time for current protection. The delay is given in seconds and can be set numerically or to the minimum/maximum value keywords.

Name	Type	Values	Description
duration	real	0.00 - 10.00	Numeric value for the initial fuse delay.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum	Use MIN/MINimum for the minimum delay or MAX/MAXimum for the maximum delay.
channel listopt	channel_list	-	Channel list.

CURR:PROT:DLEAY 1, (@1)

[SOURce:]CURRent:PROTection:LINKset / query

Sets or queries the fuses of several selected channels (fuse linking).

Name	Type	Values	Description
arg0	enum	1 \| 2	Selects the fuse linking mode.

integer - Returns 1 if channel 1 is linked with channel 2.

INST OUT1;:CURRent:PROTection:LINK 2
INST OUT1;:CURRent:PROTection:LINK?2

[SOURce:]CURRent:PROTection:TRIPped?query

Queries the OCP state of the selected channel.

Name	Type	Values	Description
channel listopt	channel_list	-	Selects the channel(s) to query.

integer - 1 indicates the OCP is tripped; 0 indicates the OCP is not tripped.

CURR:PROT:TRIP?
CURR:PROT:TRIP? (@1)

[SOURce:]CURRent:PROTection:UNLinkset / query

Unlinks fuse linking from the other channel (Ch1 or Ch2).

Name	Type	Values	Description
arg0	enum	1 \| 2	Selects which channel's fuse linking is unlinked.

CURR:PROT:UNL 1

[SOURce:]CURRent:PROTection[:STATe]set / query

Sets or queries the overcurrent protection (OCP) state of the selected channel. The setter activates or deactivates OCP; the query returns the OCP state.

Name	Type	Values	Description
arg0	integer	0 - 1	Activates or deactivates the OCP state.
channel listopt	channel_list	-	Channel list to which the command applies.

enum - Returns the OCP state of the selected channel: 1 means the OCP is tripped, 0 means the OCP is not tripped.

CURR:PROT 1
CURR:PROT? (@1)

[SOURce:]RESistance[:LEVel][:IMMediate][:AMPLitude]set / query

Sets or queries the constant resistance target value.

Name	Type	Values	Description
resistance	real	0.000 - 10000	Numeric resistance value.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum \| UP \| DOWN	Special resistance value selector or step adjustment.

RES 10
RES?
RES? MIN
RES? MAX

[SOURce:]RESistance:STATeset / query

Sets or queries the constant resistance mode for a channel.

Name	Type	Values	Description
state	enum	0 \| 1	Deactivates or activates constant resistance mode.
channel listopt	channel_list	-	Selects the channel list for the setting or query.

enum - Returns the constant resistance mode at the specified channel.

RES:STAT? (@1)

:APPLyset / query

Sets or queries the voltage and current value of the selected channel. The command provides a combined voltage/current setting in one step.

Name	Type	Values	Description
voltage	real	0.000 - 20.050	Numeric value for voltage.
currentopt	real	-	Current value to set with the voltage.
outputopt	enum	-	Output selection value.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum \| DEF \| DEFault	Keyword qualifier for the voltage parameter.

:READ?query

Queries the currently voltage-current measurement pair and returns them separated by comma.

Name	Type	Values	Description
channel listopt	channel_list	-	Channel list to query.

numeric - The voltage-current measurement pair for the selected channel or channels, returned as two numeric values separated by a comma.

READ? -> 1.001080E+00,1.004224E-02
READ? (@1)

:OUTPut:DELay:DURationset / query

Sets or queries the duration for output delay.

Name	Type	Values	Description
duration	real	0.001 - 10.00	Numeric value of the duration in seconds.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum	Selects the minimum or maximum duration value.

real (s) - Returns the duration for output delay in seconds.

:OUTPut:GENeral[:STATe]set / query

Sets or queries all previous selected channels simultaneously.

Name	Type	Values	Description
state	integer	0 - 1	Switches off or on all previously selected channels simultaneously.

enum - Returns the current state of all previously selected channels simultaneously.

:OUTPut[:STATe]set / query

Sets or queries the output state of the previous selected channels.

Name	Type	Values	Description
state	enum	0 \| 1	Switches the previous selected channels off or on.
Channel listopt	channel_list	-	Channels to query.

enum - Returns the output state of the specified channel(s).

OUTP? (@1)

:OUTPut:DELay[:STATe]set / query

Sets or queries the output delay state for the selected channel.

Name	Type	Values	Description
state	enum	0 \| 1	Deactivates or activates output delay for the selected channel.
Channel listopt	channel_list	-	Selected channel list.

enum - Returns the output delay state for the selected channel.

OUTPut:DELay 1
OUTPut:DELay? -> 1
OUTPut:DELay? (@1)

:OUTPut:FTResponseset / query

Sets or queries the fast transient response state for the selected channel.

Name	Type	Values	Description
state	enum	0 \| 1	Deactivates or activates fast transient response.
channel listopt	channel_list	-	Channel list for setting and query.

enum - Returns the fast transient response state as on for the queried channel.

OUTPut:FTResponse 1
OUTPut:FTResponse? -> 1
OUTPut:FTR? (@1)

:OUTPut:IMPedanceset / query

Sets or queries source impedance for the specified signal in ohms. The query can optionally be directed to a channel list.

Name	Type	Values	Description
resistance	real	-0.05 - 100	Numeric value of the impedance in ohms.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum \| DEF \| DEFault	Keyword shortcut for the minimum, maximum, or default impedance value.
channel listopt	channel_list	-	Channel list for the query.

real (ohm) - Returns the output impedance in ohms.

OUTPut:IMPedance 1
OUTPut:IMPedance? -> 1
OUTPut:IMPedance? (@1)

:OUTPut:IMPedance:STATeset / query

Sets or queries the impedance target for the selected channel. A state of 0 deactivates output impedance and 1 activates it.

Name	Type	Values	Description
state	enum	0 \| 1	Activates or deactivates output impedance for the selected channel.
channel listopt	channel_list	-	Selects the channel to query.

enum - Returns the output impedance state for the selected channel.

OUTPut:IMPedance:STAT? -> 1
OUTPut:IMPedance:STAT? (@1)

:OUTPut:MODEset / query

Sets or queries the output mode. The power supply can operate in auto, sink, or source mode depending on the selected setting.

Name	Type	Values	Description
arg0	enum	AUTO \| SINK \| SOURce	Output mode to set.
Channel listopt	channel_list	-	Channel or channels to which the command applies.

enum - Returns the output mode of the specified channel(s).

OUTPut:MOD? (@1)
OUTPut:MOD AUTO, (@1)

:OUTPut:SELectset / query

Sets or queries the output state of the selected channel.

Name	Type	Values	Description
state	enum	0 \| 1	Deactivates or activates the selected channel.

OUTPut:SEL? (@1)
OUTPut:SEL? (@1)

:OUTPut:TRIGgeredset / query

Enables or disables the triggered event for output. The setting can be applied to one or more channels.

Name	Type	Values	Description
arg0	boolean	-	Enables (1) or disables (0) the trigger event for output.
Channel listopt	channel_list	-	Channel list to which the setting applies.

OUTP:TRIG 1
OUTPut:TRIG? (@1)

:OUTPut:TRIGgered:BEHaviorset / query

Sets or queries the output behavior when a trigger event occurs.

Name	Type	Values	Description
arg0	enum	ON \| OFF \| GATed	Output behavior to apply when a trigger event occurs.
channel listopt	channel_list	-	Channel list.

OUTP:TRIG:BEH ON
OUTPut:TRIG:BEH? (@1)

:OUTPut:TRIGgered[:STATe]set / query

Enables or disables the triggered event for output. The setting applies to the specified channel list.

Name	Type	Values	Description
arg0	enum	1 \| 0	Enables or disables the triggered event.
channel listopt	channel_list	-	Channel list to which the setting applies.

OUTP:TRIG 1
OUTPut:TRIG? (@1)

:SENSe:CURRent:RANGe:AUTOset / query

Sets or queries auto range for current measurement accuracy.

Name	Type	Values	Description
arg0	boolean	-	Enables or disables auto range for current.
Channel listopt	channel_list	-	Channel list to apply the command to.

SENS:CURR:RANG:AUTO 1

:SENSe:CURRent:RANGe[:UPPer]set / query

Sets or queries the current range for measurement. There is a selection of 10 A, 1 A, 100 mA and 10 mA range.

Name	Type	Values	Description
arg0	real	A	Defines the current range for measurement.
Channel listopt	channel_list	-	Channel list.

real (A) - Returns the current range for measurement.

SENS:CURR:RANG 10
SENS:CURR:RANG? (@1)

:SENSe:VOLTage:RANGe:AUTOset / query

Sets or queries auto range for voltage measurement accuracy.

Name	Type	Values	Description
arg0	enum	1 \| 0	Enables or disables auto range for voltage.
channel listopt	channel_list	-	Channel list.

SENS:VOLT:RANG:AUTO 1
SENS:VOLT:RANG:AUTO? (@1)

:SENSe:VOLTage:RANGe[:UPPer]set / query

Sets or queries the voltage range for measurement. There is a selection of 20 V and 5 V range.

Name	Type	Values	Description
arg0	real	V	Defines the voltage range for measurement.
Channel listopt	channel_list	-	Channel list.

real (V) - Returns the present voltage range for measurement.

SENS:VOLT:RANG 20
SENS:VOLT:RANG? (@1)

:FUSE:DELay:INITialset / query

Sets or queries the initial delay time for the fuse to take effect.

Name	Type	Values	Description
delay	real	0.00 - 60.00	Numeric value for initial fuse delay; MIN/MAX keywords are also accepted.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum	Selects the minimum or maximum initial fuse delay value.
channel listopt	channel_list	-	Channel list for setting or querying the command.

FUSE:DEL:INIT? (@1)

:FUSE:DELay[:BLOWing]set / query

Sets or queries the delay time for the fuse to take effect. The query returns the fuse delay time for the specified channel.

Name	Type	Values	Description
delay	real	0.00 - 10.00	Numeric value for the fuse delay; MIN and MAX keywords are also accepted.
qualifieropt	enum	MIN \| MINimum \| MAX \| MAXimum	Optional keyword qualifier for the delay value.
channel listopt	channel_list	-	Channel list for setting or querying the fuse delay.

real (s) - Returns the fuse delay time for the specified channel.

FUSE:DEL? (@1)

:FUSE:LINKset / query

Sets or queries the fuse-linking relationship between selected channels. The value 1 or 2 selects which channel is linked with the other channel.

Name	Type	Values	Description
arg0	enum	1 \| 2	Selects the fuse-linking channel relationship.

integer - Returns 1 if channel 1 is linked with channel 2, as shown in the example query.

INST OUT1;:FUSE:LINK 2
INST OUT1;:FUSE:LINK?2

:FUSE:TRIPped?query

Queries whether the fuse has tripped in the selected channel.

Name	Type	Values	Description
Channel listopt	channel_list	-	Channel or channels to query.

boolean - Returns the fuse tripped status of the selected channel.

FUSE:TRIP? (@1)

:FUSE:UNLinkset / query

Dissolves linked fuses.

Name	Type	Values	Description
channel	integer	1 - 2	Channel to unlink.

:FUSE[:STATe]set / query

Sets or queries the fuse function in the selected channel.

Name	Type	Values	Description
state	integer	0 - 1	Activates or deactivates the fuse function.
channel listopt	channel_list	-	Selects the channels to query.

integer - Returns the fuse function state of the selected channel: 1 if activated, 0 if not activated.

FUSE? (@1)
FUSE:PROT?

[SOURce:]POWer:PROTection[:STATe]set / query

Sets or queries the over power protection (OPP) state of the previously selected channel. The query form can optionally take a channel list.

Name	Type	Values	Description
state	boolean	-	OPP state to set for the previous selected channel.
channel listopt	channel_list	-	Channels for which to query the OPP state.

boolean - Returns the OPP state of the previous selected channel.

[SOURce:]POWer:PROTection[:STATe] <state>
[SOURce:]POWer:PROTection[:STATe]? [<Channel list>]

:SOURce:POWer:PROTection:CLEarset / query

Resets the OPP state of the selected channel. If an OPP event occurred before, the reset also erases the message on the display.

Name	Type	Values	Description
channel listopt	channel_list	-	Selected channel(s) to reset.

:SOURce:POWer:PROTection:CLEar (@1)

:SOURce:POWer:PROTection:LEVelset / query

Sets the overpower protection level of the selected channel, or queries it with the optional channel list. The level is given as a numeric power value in watts and may also be set to the minimum, maximum, or default value keywords.

Name	Type	Values	Description
power	real	0.00 - 65.35050E+00	Numeric value of the power protection level in watts.
qualifieropt	enum	MINimum \| MAXimum \| DEFault	Use MINimum for 0.00 W, MAXimum for 65.35050E+00 W, or DEFault for the default value 65.35050E+00 W.

:SOURce:POWer:PROTection:LEVel?query

Queries the overpower protection level of the selected channel. The level is specified in watts and the query supports an optional channel list.

Name	Type	Values	Description
channel listopt	channel_list	-	Channel or channels to query.

real (W) - Returns the overpower protection level of the selected channel in watts.

POW:PROT? (@1)

:SOURce:POWer:PROTection:TRIPped?query

Queries the OPP state of the selected channel. Response 1 means the OPP is tripped; response 0 means the OPP is not tripped.

Name	Type	Values	Description
channel listopt	channel_list	-	Selects the channel to query.

enum - Returns 1 if the OPP is tripped and 0 if the OPP is not tripped.

POW:PROT:TRIP?
POW:PROT:TRIP? (@1)

:INTerfaces:GPIB:ADDRessset / query

Sets or queries the GPIB address.

Name	Type	Values	Description
gpib address	integer	0 - 20	GPIB address.

INT:GPIB:ADDR 20

:INTerfaces:USB:CLASsset / query

Sets or queries the USB class. The USB class can be set to CDC or TMC.

Name	Type	Values	Description
USB class	enum	CDC \| TMC	USB interface class to use.

:MEASure[:SCALar]:ENERgy?query

Queries the measured accumulated energy value of the previously selected channel.

Name	Type	Values	Description
channel listopt	channel_list	-	Channel list identifying the channel to query.

real (Wh) - Measured accumulated energy value.

MEAS:ENER? -> 5.382E+00 (value in Wh)
MEAS:ENER? (@1)

:MEASure[:SCALar]:ENERgy:RESetset / query

Resets the energy counter for the selected channel.

Name	Type	Values	Description
channel listopt	channel_list	-	Selected channel list.

MEAS:ENER:RES (@1)

:MEASure[:SCALar]:ENERgy:STATeset / query

Sets or queries the energy counter state for the selected channel.

Name	Type	Values	Description
state	enum	1 \| 0	Activates or deactivates the energy counter.
channel listopt	channel_list	-	Channel list for the selected channel.

enum - Returns the energy counter state for the selected channel.

MEAS:ENER:STAT ON
MEAS:ENER:STAT?
MEAS:ENER:STAT? -> 1
MEAS:ENER:STAT? (@1)

:MEASure[:SCALar]:ENERgy:STATe?query

Queries the energy counter state for the selected channel.

Name	Type	Values	Description
channel listopt	channel_list	-	Channel list to query.

enum - Returns the energy counter state for the selected channel. 1 means the energy counter is activated; 0 means it is deactivated.

MEAS:ENER:STAT?
MEAS:ENER:STAT? (@1)

:MEASure[:SCALar]:ENERgy:UNITset / query

Sets or queries the measured unit for energy.

Name	Type	Values	Description
arg0	enum	WS \| WH	Measured energy unit.

MEAS:ENER:UNIT WH

:MEASure[:SCALar]:ENERgy:UNIT?query

Queries the measured unit for energy.

enum - Returns the measured energy unit for the selected channel.

:MEASure[:SCALar]:STATistic:COUNt?query

Queries the number of measurements.

integer - Returns the number of measurements.

:MEASure[:SCALar]:CURRent[:DC]:AVG?query

Queries the average measured output current.

Name	Type	Values	Description
channel listopt	channel_list	-	Selected channel list.

real - Returns the average measured output current.

MEAS:CURR:DC:AVG? (@1)

:MEASure[:SCALar]:CURRent[:DC]:MAX?query

Queries the maximum measured output current.

Name	Type	Values	Description
channel listopt	channel_list	-	Selects the channel to query.

real - The maximum measured output current.

MEAS:CURR:DC:MAX? (@1)

:MEASure[:SCALar]:CURRent[:DC]?query

Queries the currently measured current of the selected channel. Query only.

Name	Type	Values	Description
channel listopt	channel_list	-	Selected channel list.

returns - Currently measured current of the selected channel.

MEAS:CURR? -> 1.000E +00
MEAS:CURR? (@1)

:MEASure[:SCALar]:STATistic:RESetset / query

Resets the minimum, maximum and average statistics values for voltage, current, and power. It also resets the measured energy.

Name	Type	Values	Description
channel listopt	channel_list	-	Selects the channel list to reset.

MEAS:STAT:RES (@1)

:MEASure[:SCALar]:CURRent[:DC]:MIN?query

Queries the minimum measured output current.

Name	Type	Values	Description
channel listopt	channel_list	-	Selected channel list.

real - Minimum measured output current of the selected channel.

MEAS:CURR:DC:MIN? (@1)

:MEASure[:SCALar]:CURRent[:DC]:STATistic?query

Queries the current statistics of the selected channel.

Name	Type	Values	Description
<Channel list>opt	channel_list	-	Selected channel list.

returns

MEAS:CURR:DC:STAT? (@1)
MEAS:CURR:DC:STAT?

:MEASure[:SCALar]:POWer?query

Queries the currently emitted power of the selected channel.

Name	Type	Values	Description
channel listopt	channel_list	-	Selected channel list.

real - Currently emitted power of the selected channel.

MEAS:POW? -> 3.00E+00
MEAS:POW? (@1)

:MEASure[:SCALar][:POWer]:AVG?query

Queries the average measured output power.

Name	Type	Values	Description
channel listopt	channel_list	-	Selects the channel to query.

real - Returns the average measured output power.

MEAS:POW:AVG? (@1)

:MEASure[:SCALar]:POWer:STATistic?query

Queries the power statistics of the selected channel.

Name	Type	Values	Description
<Channel list>opt	channel_list	-	Selects the channel list to query.

string - Returns the power statistics of the selected channel.

MEAS:POW:STAT? (@1)

:MEASure[:SCALar][:POWer]:MAX?query

Queries the maximum measured output power.

Name	Type	Values	Description
channel listopt	channel_list	-	Selects the channel list to query.

real - Maximum measured output power of the selected channel.

MEAS:POW:MAX? (@1)

:MEASure[:SCALar][:POWer]:MIN?query

Queries the minimum measured output power for the selected channel.

Name	Type	Values	Description
channel listopt	channel_list	-	Channel list to query.

real - Returns the minimum measured output power.

MEAS:POW:MIN? (@1)

:MEASure[:SCALar][:VOLTage][:DC]:AVG?query

Queries the average measured output voltage.

Name	Type	Values	Description
channel listopt	channel_list	-	Selects the channel(s) to query.

returns

:MEASure[:SCALar][:VOLTage][:DC]?query

Queries the currently measured voltage of the selected channel.

Name	Type	Values	Description
channel listopt	channel_list	-	Selected channel list.

real - Currently measured voltage of the selected channel.

MEAS:VOLT? -> 1.000E+00
MEAS:VOLT? (@1)

:MEASure:VOLTage:DVM?query

Queries the voltmeter measurement if DVM is enabled.

Name	Type	Values	Description
<Channel list>opt	channel_list	-	Channel list identifying the channel to query.

returns

:MEASure[:SCALar][:VOLTage][:DC]:MAX?query

Queries the maximum measured output voltage.

Name	Type	Values	Description
<Channel list>opt	channel_list	-	Selected channel list.

real - Maximum measured output voltage.

MEAS:VOLT:MAX? (@1)

:MEASure[:SCALar][:VOLTage][:DC]:MIN?query

Queries the minimum measured output voltage.

Name	Type	Values	Description
channel listopt	channel_list	-	Selects the channel to query.

real - The minimum measured output voltage.

MEAS:VOLT:MIN? (@1)

:MEASure[:SCALar][:VOLTage][:DC]:STATistic?query

Queries the voltage statistics of the selected channel.

Name	Type	Values	Description
channel listopt	channel_list	-	Selects the output channel or channels to query.

returns

MEAS:VOLT:STAT? (@1)

:ARBitrary:BEHavior:ENDset / query

Sets or queries the arbitrary endpoint behavior when the arbitrary function is finished.

Name	Type	Values	Description
state	enum	HOLD \| OFF	Selects how the channel behaves after the arbitrary function is finished.

enum - Returns the arbitrary endpoint behavior of the selected channel.

:ARBitrary:BEHavior:END?query

Sets or queries the arbitrary endpoint behavior when the arbitrary function is finished.

Name	Type	Values	Description
state	enum	HOLD \| OFF	Selects the endpoint behavior for the arbitrary function.

enum - Returns the arbitrary endpoint behavior for the finished arbitrary function.

:ARBitrary[:STATe]set / query

Sets or queries the arbitrary function state for the previously selected channel. A channel list can be supplied with the setting or query form to address specific channels.

Name	Type	Values	Description
state	enum	1 \| 0	Activates or deactivates the arbitrary function.
channel listopt	channel_list	-	Channel list to set or query.

enum - Returns the arbitrary function state for the addressed channel(s).

ARB ON
ARB? -> 1
ARB ON, (@1)
ARB? (@1)

:ARBitrary[:STATe]?query

Sets or queries the arbitrary function for the previously selected channel. The query can optionally specify a channel list.

Name	Type	Values	Description
state	enum	1 \| 0	Activates or deactivates the arbitrary function.
channel listopt	channel_list	-	Channel list to set or query.

enum - Returns the arbitrary function state for the selected channel(s).

ARB ON
ARB? -> 1
ARB ON, (@1)
ARB? (@1)

:ARBitrary:CLEarset / query

Clears the current arbitrary table data for the selected channel.

ARBitrary:CLEar

:ARBitrary:DATAset / query

Sets or queries the arbitrary points for the previously selected channel. Up to 4096 arbitrary points can be defined, with dwell time between points from 1 ms to 20 days.

Name	Type	Values	Description
data	string	-	Voltage, current, time, and interpolation mode values for one or more arbitrary points.

string - Returns the defined arbitrary points for the previously selected channel.

ARB:DATA 10,1,0.5,0
ARB:DATA? -> 10.000, 1.000, 0.50, 0

:ARBitrary:FNAMeset / query

Sets or queries the file name and storage location for the arbitrary function.

Name	Type	Values	Description
filename	string	-	Filename of the arbitrary function.
locationopt	enum	INT \| EXT \| DEF	Storage location for the arbitrary function.

string - Returns the arbitrary function file name for the specified location.

ARB:FNAM "01.CSV"
ARB:FNAM? INT -> "01.CSV"

:ARBitrary:FNAMe?query

Queries the file name and storage location for the arbitrary function. An optional location can be supplied to select internal memory, USB stick, or default internal memory.

Name	Type	Values	Description
locationopt	enum	INT \| EXT \| DEF	Selects the storage location to query.

string - Returns the file name of the arbitrary function.

ARB:FNAM? INT -> "01.CSV"

:ARBitrary:LOADset / query

Loads an arbitrary table from a file specified with ARB:FNAM.

:ARBitrary:REPetitionsset / query

Sets or queries the repetition rate of the defined arbitrary waveform for the previously selected channel. A repetition rate of 0 means the waveform repeats infinitely.

Name	Type	Values	Description
repetition_rate	integer	0 - 65535	Repetition rate of the arbitrary waveform; 0 indicates infinite repetition.

integer - Returns the repetition rate of the Ch1 arbitrary waveform.

ARB:REP 10
ARB:REP? -> 10

:ARBitrary:REPetitions?query

Sets or queries the repetition rate of the defined arbitrary waveform for the previously selected channel. A value of 0 means infinite repetition.

integer - Returns the repetition rate of the arbitrary waveform for the previously selected channel.

ARB:REP? -> 10

:ARBitrary:RESToreset / query

Loads an arbitrary table from a file specified with ARB:FNAM. The example indicates it restores arbitrary data from ARB03.CSV.

:ARBitrary:SAVEset / query

Saves the current arbitrary table to a file specified with ARB:FNAM.

:ARBitrary:STARtset / query

Enables arbitrary for the selected channel. Command is the same as ARB:STAT 1.

:ARBitrary:STOPset / query

Disables arbitrary for the selected channel. This command is the same as ARB:STAT 0.

:ARBitrary:TRANsferset / query

Transfers the defined arbitrary table to the selected channel.

Name	Type	Values	Description
channel	integer	1 - 2	Selected channel.

:ARBitrary:TRIGgered:MODEset / query

Sets or queries the arbitrary trigger mode of the previously selected channel.

Name	Type	Values	Description
mode	enum	SINGle \| RUN	Trigger mode for arbitrary operation.

enum - Returns the current arbitrary trigger mode.

:ARBitrary:TRIGgered:MODE?query

Sets or queries the arbitrary trigger mode of the previously selected channel.

enum - Returns the current arbitrary trigger mode.

:ARBitrary:TRIGgered[:STATe]set / query

Sets or queries the arbitrary trigger mode.

Name	Type	Values	Description
state	enum	OFF \| ON	Activates or deactivates the trigger input.

integer - Returns the arbitrary trigger mode state.

ARB:TRIG ON
ARB:TRIG? -> 1

:ARBitrary:TRIGgered[:STATe]?query

Sets or queries the arbitrary trigger mode.

Name	Type	Values	Description
state	enum	OFF \| ON	Activates or deactivates the trigger input.

enum - Returns the arbitrary trigger mode.

INST OUT1
ARB:TRIG ON
ARB:TRIG? -> 1

:BATTery:SIMulator:CAPacity:LIMitset / query

Sets or queries the full battery capacity for the specific channel.

Name	Type	Values	Description
arg0	real	-	Defines the full battery capacity.

INST:NSEL 1
BATT:SIM:CAP:LIM 100

:BATTery:SIMulator:CAPacity:LIMit?query

Queries the full battery capacity for the specific channel.

real - Returns the full battery capacity for the specific channel.

INST:NSEL 1
BATT:SIM:CAP?

:BATTery:SIMulator:CAPacity?query

Queries the remaining battery capacity from the specific channel.

real - Returns the remaining battery capacity for the selected channel.

:BATTery:SIMulator:CURRent:LIMit?query

Queries the current limit from the specific channel of the battery simulator.

real (A) - Returns the current limit from the specific channel.

INST:NSEL 1
BATT:SIM:CURR:LIM?

:BATTery:SIMulator:CURRent?query

Queries the current of the battery simulator from the specific channel.

real (A) - Returns the current from the channel's battery simulator.

INST:NSEL 1
BATT:SIM:CURR?

:BATTery:SIMulator:CURRent:LIMit:EOCset / query

Sets or queries the current limit at end-of-charge.

Name	Type	Values	Description
arg0	-	-	Sets the current limit at end-of-charge.

returns - Returns current limit at end-of-charge for channel 1.

INST:NSEL 1
BATT:SIM:CURR:LIM:EOC?

:BATTery:SIMulator:CURRent:LIMit:EOC?query

Sets or queries the current limit at end-of-charge.

Name	Type	Values	Description
arg0	-	-	Sets the current limit at end-of-charge.

returns - Returns current limit at end-of-charge for channel 1.

INST:NSEL 1
BATT:SIM:CURR:LIM:EOC?

:BATTery:SIMulator:CURRent:LIMit:EODset / query

Sets or queries the current limit at end-of-discharge.

Name	Type	Values	Description
arg0	real	-	Sets the current limit at end-of-discharge.

real - Returns current limit at end-of-discharge for channel 1.

BATT:SIM:CURR:LIM:EOD?

:BATTery:SIMulator:CURRent:LIMit:EOD?query

Sets or queries the current limit at end-of-discharge.

Name	Type	Values	Description
arg0	-	-	Sets the current limit at end-of-discharge.

returns - Returns current limit at end-of-discharge for channel 1.

INST:NSEL 1
BATT:SIM:CURR:LIM:EOD?

:BATTery:SIMulator:CURRent:LIMit:REGularset / query

Sets or queries the current limit at regular charge level.

Name	Type	Values	Description
arg0	real	-	Sets the current limit at regular charge level.

real - Returns current limit at regular charge level for channel 1.

INST:NSEL 1
BATT:SIM:CURR:LIM:REG?

:BATTery:SIMulator:CURRent:LIMit:REGular?query

Sets or queries the current limit at regular charge level.

Name	Type	Values	Description
arg0	-	-	Sets the current limit at regular charge level.

returns - Returns current limit at regular charge level for channel 1.

INST:NSEL 1
BATT:SIM:CURR:LIM:REG?

:BATTery:SIMulator:RESistance?query

Queries the battery simulator internal resistance (ESR).

real - Returns the battery simulator internal resistance (ESR) for the selected channel.

INST:NSEL 1
BATT:SIMU:RES?

:BATTery:SIMulator:SOCset / query

Sets or queries the state of charge (SoC) of the battery simulator.

Name	Type	Values	Description
arg0	real	-	Sets the state of charge (SoC) of the battery simulator.

returns

:BATTery:SIMulator:SOC?query

Sets or queries the state of charge (SoC) of the battery simulator.

Name	Type	Values	Description
arg0	real	-	Sets the state of charge (SoC) of the battery simulator.

real - Returns the state of charge (SoC) of the battery simulator.

:BATTery:SIMulator:TVOLtage?query

Queries the terminal voltage (Vt) of the specific channel.

real (V) - Returns the channel terminal voltage of the battery simulator.

INST:NSEL 1
BATT:SIM:TVOL?

:BATTery:SIMulator:VOC:EMPTy?query

Queries the open circuit voltage (Voc) for empty SoC, i.e. SoC = 0 %.

real - Returns the channel 1 Voc of an empty charge battery.

INST:NSEL 1
BATT:SIM:VOC:EMPT?

:BATTery:SIMulator:VOC:FULL?query

Queries the open circuit voltage (Voc) for full SoC, i.e. SoC = 100 %.

integer - Returns 1 if the specified channel's battery simulator is fully charge.

INST:NSEL 1
BATT:SIM:VOC:FULL?

:BATTery:SIMulator:VOC?query

Queries the open circuit voltage (Voc) of the specific channel.

real (V) - Returns the channel open circuit voltage of the battery simulator.

INST:NSEL 1
BATT:SIM:VOC?

:BATTery:MODel:CURRent:LIMit:EOCset / query

Sets or queries the current limit of the battery model at end-of-charge.

Name	Type	Values	Description
arg0	-	-	Sets the current limit of the battery model at end-of-charge.

returns - Returns the current limit of the battery model at end-of-charge for the selected channel.

INST:NSEL 1
BATT:MODel:CURR:LIM:EOC?

:BATTery:MODel:CURRent:LIMit:EOC?query

Sets or queries the current limit of the battery model at end-of-charge.

real - Returns the current limit of the battery model at end-of-charge for the selected channel.

INST:NSEL 1
BATT:MODel:CURR:LIM:EOC?

:BATTery:SIMulator[:ENABle]set / query

Sets or queries the battery simulator state for the specific channel. The optional channel list selects the affected channel.

Name	Type	Values	Description
arg0	enum	1 \| 0	Enables or disables the battery simulator state.
Channel listopt	channel_list	-	Selects the channel list.

INST:NSEL 1
BATT:SIM 1
BATT:SIM 1, (@1)

:BATTery:SIMulator[:ENABle]?query

Sets or queries the specific channel of the battery simulator state. The query returns the battery simulator state for the specified channel list.

Name	Type	Values	Description
arg0	enum	1 \| 0	Enables or disables the battery simulator state.
channel listopt	channel_list	-	Channel list to which the setting or query applies.

enum - Battery simulator state for the specified channel.

INST:NSEL 1 BATT:SIM 1
BATT:SIM 1, (@1)

:BATTery:STATus?query

Queries the status of the battery. The status can be idle, charging, or discharging.

Name	Type	Values	Description
channel listopt	channel_list	-	Selects the channel to query.

enum - Returns the battery status.

BATT:STAT?
BATT:STAT? (@1)

:BATTery:MODel:CAPacityset / query

Sets or queries the battery model capacity.

Name	Type	Values	Description
arg0	-	-	Sets the battery model capacity.

returns - Returns the battery model capacity.

INST:NSEL 1
BATT:MODel:CAP 50

:BATTery:MODel:CAPacity?query

Sets or queries the battery model capacity.

Name	Type	Values	Description
arg0	real	-	Sets the battery model capacity.

real - Returns the battery model capacity.

INST:NSEL 1
BATT:MODel:CAP 50

:BATTery:MODel:CLEarset / query

Clears the current battery model.

INST:NSEL 1
BATT:MOD:CLE

:BATTery:MODel:CURRent:LIMit:EODset / query

Sets or queries the current limit of the battery model at end-of-discharge.

Name	Type	Values	Description
arg0	-	-	Sets the current limit of the battery model at end-of-discharge.

returns - Returns current limit of the battery model at end-of-discharge for channel 1.

INST:NSEL 1
BATT:MODel:CURR:LIM:EOD?

:BATTery:MODel:CURRent:LIMit:EOD?query

Sets or queries the current limit of the battery model at end-of-discharge.

real - Returns the current limit of the battery model at end-of-discharge for the selected channel.

INST:NSEL 1
BATT:MODel:CURR:LIM:EOD?

:BATTery:MODel:CURRent:LIMit:REGularset / query

Sets or queries the current limit of the battery model at regular charge level.

Name	Type	Values	Description
arg0	-	-	Sets the current limit of the battery model at regular charge level.

INST:NSEL 1
BATT:MODel:CURR:LIM:REG?
Returns current limit of the battery model at regular charge level for channel 1.

:BATTery:MODel:CURRent:LIMit:REGular?query

Sets or queries the current limit of the battery model at regular charge level.

real - Returns current limit of the battery model at regular charge level for the selected channel.

INST:NSEL 1
BATT:MODel:CURR:LIM:REG?

:BATTery:MODel:DATAset / query

Sets or queries the battery model data.

Name	Type	Values
arg0	-	-
arg1	-	-
arg2	-	-

:BATTery:MODel:DATA?query

Sets or queries the battery model data.

returns

:BATTery:MODel:FNAMeset / query

Sets or queries a filename for the battery model. An optional partition selects internal memory, USB storage, or the default storage partition.

Name	Type	Values	Description
Filename	string	-	Filename for the battery model.
Partitionopt	enum	INT \| EXT \| DEF	Selects partition for file storage.

BATT:MOD:FNAM "NEwBattery.csv",INT

:BATTery:MODel:FNAMe?query

Sets or queries a filename for the battery model. An optional partition can be specified for file storage.

Name	Type	Values	Description
Filename	string	-	Filename for the battery model.
Partitionopt	enum	INT \| EXT \| DEF	Selects the partition for file storage.

string - Returns the battery model filename, optionally followed by the storage partition.

BATT:MOD:FNAM "NEwBattery.csv",INT

:BATTery:MODel:ISOCset / query

Sets or queries the initial state of charge (SoC) of the battery model.

Name	Type	Values	Description
State_of_charge	real	%	Initial state of charge (SoC) for the battery model.

real (%) - Returns the initial state of charge (SoC) of the battery model.

BATT:MOD:ISOC 50
BATT:MOD:ISOC?

:BATTery:MODel:ISOC?query

Sets or queries the initial state of charge (SoC) of the battery model.

Name	Type	Values	Description
State_of_charge	real	%	Initial state of charge (SoC) for the battery model.

real (%) - Returns the initial state of charge (SoC) of the battery model.

BATT:MOD:ISOC 50

:BATTery:MODel:LOADset / query

Loads a battery model for editing.

Name	Type	Values	Description
filename	string	-	Filename for the battery model.

BATT:MOD:LOAD

:BATTery:MODel:SAVEset / query

Saves the current battery model to a file.

BATT:MOD:SAVE

:BATTery:MODel:TRANsferset / query

Transfers the loaded battery model into the specified channel.

Name	Type	Values	Description
channel	integer	1 - 2	Channel to receive the loaded battery model.

BATT:MOD:TRAN 1

:DATA:DATA?query

Returns the logging file data of the selected file. In manual trigger mode, the logging function must be activated before the instrument can save a logging file internally or on the USB stick.

Name	Type	Values	Description
filepath	string	-	Filepath of the logging file data.

string - Returns the logging file data of the selected file.

:DATA:DELeteset / query

Deletes the specified file from memory.

Name	Type	Values	Description
filepath	string	-	Filepath of the file.

:DATA:LIST?query

Queries all files in internal memory ('/int/') and external memory ('/USB').

string - Returns a comma-separated list of file paths.

DATA:LIST? -> "/USB1/NGL201/logging/log-20201203T101025.829.csv", "/int/arb/newWaveform.csv","/int/logging/log-20210301T101129.818.csv"

:DATA:POINts?query

Queries the number of measurements from the selected logging file. In manual trigger mode, the logging function must be activated or the instrument cannot save a logging file internally or on the USB stick.

Name	Type	Values	Description
filepath	string	-	Filepath of the logging file data.

integer - Returns the number of measurements in the specified logging file.

DATA:POIN?
"/USB1/NGL201/logging/log-20201203T101025.829.csv" -> 5

:HCOPy:DATA?query

Returns the actual display content as a screenshot.

block - The actual display content (screenshot).

:HCOPy:SIZE:X?query

Returns the horizontal dimension of the screenshots.

integer - The horizontal dimension of the screenshots.

:HCOPy:SIZE:Y?query

Returns the vertical dimension of the screenshots.

integer - The vertical dimension of the screenshots.

:FLOG:DATA?query

Queries FastLog data as a binary block. The block contains voltage and current measurements in the sequence V, I, V, I, ....

block - Returns FastLog data as a binary block in the format #<LengthofLength><Length><block_data>.

FLOG:DATA?

:FLOG[:STATe]set / query

Sets or queries the FastLog state.

Name	Type	Values	Description
arg0	enum	1 \| 0	Enables or disables the FastLog state.

enum - Returns the FastLog state.

FLOG 1

:FLOG:SRATeset / query

Sets or queries the sample rate of the FastLog function.

Name	Type	Values	Description
samplerate	enum	S500k \| S250k \| S050k \| S50k \| S010k \| S10k \| S001k \| S1k \| S100	FastLog sample rate setting.

FLOG:SRATE S050K
FLOG:SRATE?-> S050k
FLOG:SRATE S050k
FLOG:SRATE?-> S050k
FLOG:SRATE S1k
FLOG:SRATE?-> S001k

:FLOG:STIMeset / query

Sets or queries the samples accumulate duration in seconds.

Name	Type	Values	Description
arg0	real	s	Samples accumulate duration.

:FLOG:TRIGgeredset / query

Sets or queries the triggered state of FastLog. Use 1 to activate FastLog and 0 to deactivate it.

Name	Type	Values	Description
arg0	integer	0 - 1	Triggered state of FastLog.

integer - Returns the triggered state of FastLog.

FLOG:TRIG 1

:FLOG:WFILeset / query

Sets the FastLog data to be written to an external file.

Name	Type	Values	Description
arg0	enum	1 \| 0	Activates or deactivates writing the FastLog to an external file.

FLOG:WFIL 1

:FLOG:WFILe:DURationset / query

Sets or queries the file writes duration.

Name	Type	Values	Description
duration	real	s	Sets file writes duration.

:FLOG:WFILe:TPARtitionset / query

Selects the external partition to which FastLog data is written.

Name	Type	Values	Description
arg0	string	-	Defines the external path partition to which the data is written in the USB stick.

FLOG:WFIL:TPAR "/USB1A/NGM202"

:LOG[:STATe]set / query

Sets or queries the data logging state.

Name	Type	Values	Description
state	enum	1 \| 0	Enables or disables the data logging function.

enum - Returns the data logging state.

:LOG:COUNtset / query

Sets or queries the number of measurement values to be captured. The setter accepts a numeric count or the keywords MIN/MAX; the query can return the minimum or maximum allowed count when qualified.

Name	Type	Values	Description
count	integer	1 - 10000000	Number of measurement values to be captured.
qualifieropt	enum	MINimum \| MAXimum	When used with the query, returns the minimum or maximum number of measurement values.

integer - Returns the number of measurement values.

LOG:COUN MAX
LOG:COUN? MAX -> 10000000

:LOG:DURationset / query

Sets or queries the duration of the data logging. The duration can be set as a numeric value in seconds, or to the minimum or maximum allowed value.

Name	Type	Values	Description
span	real	0 - 3.49*10^5	Duration of the data logging.
qualifieropt	enum	MINimum \| MAXimum	Returns the duration for the minimum or maximum setting.

real (s) - Returns the duration of the data logging.

LOG:DUR MAX
LOG:DUR? MAX -> 349000

:LOG:FNAMe?query

Queries the filename and storage location for the data logging. This is a query only command.

string - Returns the data log filename and storage location.

LOG 0
LOG:FNAM? -> ""
LOG 1
LOG:FNAM? -> "/int/logging/log-20190318T1141853.407.csv"

:LOG:INTervalset / query

Sets or queries the data logging measurement interval. The measurement interval describes the time between recorded measurements.

Name	Type	Values	Description
interval	real	0.1 - 600	Measurement interval.

real (s) - Returns the measurement interval.

LOG:INT 10
LOG:INT? -> 10

:LOG:MODEset / query

Sets or queries the data logging mode.

Name	Type	Values	Description
mode	enum	UNLimited \| COUNt \| DURation \| SPAN	Selects the data logging mode.

enum - Returns the current data logging mode.

:LOG:STIMeset / query

Sets or queries the start time of the data logging function.

Name	Type	Values	Description
Year	integer	-	Sets the year for the data logging function.
Month	integer	-	Sets the month for the data logging function.
Day	integer	-	Sets the day for the data logging function.
Hour	integer	-	Sets the hour for the data logging function.
Minute	integer	-	Sets the minute for the data logging function.
Second	integer	-	Sets the second for the data logging function.

string - Returns the start time of the data logging function as year, month, day, hour, minute, second.

LOG:STIM 2018,08,18,08,18,18
LOG:STIM? -> 2018,08,18,08,18,18

:LOG:TRIGgeredset / query

Sets or queries the state for the manual trigger logging function.

Name	Type	Values	Description
state	enum	0 \| 1	Manual trigger logging function state.

enum - Returns the manual trigger logging function state.

LOG:TRIG ON
LOG:TRIG? -> 1

:STATus:OPERation:INSTrument:CONDition?query

Returns the contents of the CONDition part of the status register for checking operation instrument or measurement states. Reading the CONDition register does not delete its contents.

integer - Condition bits in decimal representation.

:STATus:OPERation:INSTrument:ENABleset / query

Controls the ENABle part of the STATus:OPERation register. It defines which events in the EVENt part of the status register are forwarded to the OPERation summary bit of the status byte.

Name	Type	Values	Description
Enable	integer	1 - 65535	Enable mask value.

:STATus:OPERation:INSTrument:ISUMmary<Channel>:CONDition?query

Returns the contents of the CONDition part of the status register for the selected instrument or measurement state summary channel. Reading the CONDition register does not delete its contents.

Name	Type	Values	Description
channel	integer	1 - n	Selects the instrument channel.

integer - Condition bits in decimal representation.

:STATus:OPERation:INSTrument:ISUMmary<Channel>:ENABleset / query

Controls the ENABle part of the STATus:OPERation register for the selected instrument channel summary. The enable mask defines which events in the EVENt part of the status register are forwarded to the OPERation summary bit.

Name	Type	Values	Description
enable	integer	1 - 65535	Enable mask for operation status reporting.

:STATus:OPERation:INSTrument:ISUMmary<Channel>:NTRansitionset / query

Sets or queries the negative transition filter for the instrument status register summary of a channel. Setting a bit causes a 1-to-0 transition in the corresponding condition-register bit to set the associated event-register bit.

Name	Type	Values	Description
Channel	integer	1 - n	Channel suffix identifying the summary register instance.
NegativeTransition	integer	1 - 65535	Bit mask for the negative transition filter.

integer - Returns the current negative transition filter setting.

STATus:OPERation:INSTrument:ISUMmary1:NTRansition?

:STATus:OPERation:INSTrument:ISUMmary<Channel>:PTRansitionset / query

Sets or queries the positive transition filter for the specified status operation instrument summary channel. Setting a bit in the filter causes a 0 to 1 transition in the corresponding condition-register bit to write a 1 to the associated event-register bit.

Name	Type	Values	Description
channel	integer	1 - n	Summary channel number.
positiveTransition	integer	1 - 65535	Positive transition filter value.

integer - Returns the positive transition filter value.

:STATus:OPERation:INSTrument:ISUMmary<Channel>[:EVENt]?query

Returns the contents of the EVENt part of the status register for the specified channel. Reading an EVENt register deletes its contents.

integer - Event register contents.

:STATus:OPERation:INSTrument:NTRansitionset / query

Sets or queries the negative transition filter. Setting a bit in the filter causes a 1-to-0 transition in the associated condition register to set the corresponding bit in the event register.

Name	Type	Values	Description
negativeTransition	integer	1 - 65535	Negative transition filter bit mask.

integer - Returns the negative transition filter value.

STATus:OPERation:INSTrument:ISUMmary1:NTRansition?

:STATus:OPERation:INSTrument:PTRansitionset / query

Sets or queries the positive transition filter. Setting a bit in the positive transition filter causes a 0 to 1 transition in the corresponding condition register bit to write a 1 in the corresponding event register bit.

Name	Type	Values	Description
positiveTransition	integer	1 - 65535	Bit mask for the positive transition filter.

:STATus:OPERation:INSTrument[:EVENt]?query

Returns the contents of the EVENt part of the status register to check whether an event has occurred since the last reading. Reading an EVENt register deletes its contents.

integer - Event register contents.

:STATus:QUEStionable:INSTrument:CONDition?query

Returns the contents of the CONDition part of the questionable instrument status register. Reading the CONDition register does not delete its contents.

integer - Condition bits in decimal representation.

:STATus:QUEStionable:INSTrument:ENABleset / query

Sets or queries the enable mask that allows true conditions in the EVENt part to be reported in the summary bit. If a bit in the ENABle part is 1 and the corresponding EVENt bit is true, a positive transition occurs in the summary bit.

Name	Type	Values	Description
<arg0>	integer	0 - 65535	Enable mask value.

:STATus:QUEStionable:INSTrument:ISUMmary<Channel>:CONDition?query

Returns the contents of the CONDition part of the status register for the selected instrument or measurement state. Reading the CONDition register does not delete its contents.

Name	Type	Values	Description
Channel	integer	1 - n	Selects the instrument.

integer - Condition bits in decimal representation.

:STATus:QUEStionable:INSTrument:ISUMmary<Channel>:ENABleset / query

Name	Type	Values	Description
<Channel>	integer	1 - n	Selects the instrument; the suffix <n> at Channel selects the instrument.

:STATus:QUEStionable:INSTrument:ISUMmary<Channel>:NTRansitionset / query

Sets or queries the negative transition filter for the selected channel summary register. Setting a bit causes a 1 to 0 transition in the corresponding condition register bit to set the associated event register bit.

Name	Type	Values	Description
NegativeTransition	integer	1 - 65535	Bit mask in decimal representation.

integer - Event bits in decimal representation from the queried negative transition status register.

STATus:QUEStionable:INSTrument:ISUMmary1:NTRansition?

:STATus:QUEStionable:INSTrument:ISUMmary<Channel>[:EVENt]?query

Returns the contents of the EVENt part of the status register for the specified channel summary. Reading the EVENt register clears its contents.

Name	Type	Values	Description
Channel	integer	1 - n	Status register channel index.

integer - Event bits in decimal representation.

:STATus:QUEStionable:INSTrument:NTRansitionset / query

Sets or queries the negative transition filter for the questionable instrument status register. A set bit causes a 1-to-0 transition in the corresponding condition register bit to set the matching event register bit.

Name	Type	Values	Description
NegativeTransition	integer	1 - 65535	Bit mask for the negative transition filter.

integer - Event bits in decimal representation from the queried negative transition/status register.

STATus:QUEStionable:INSTrument:ISUMmary1: NTRansition?

:STATus:QUEStionable:INSTrument[:EVENt]?query

Returns the contents of the EVENt part of the status register to check whether an event has occurred since the last reading. Reading an EVENt register deletes its contents.

integer - Event bits in decimal representation.

:STATus:QUEStionable:INSTrument:ISUMmary<Channel>:PTRansitionset / query

Sets or queries the positive transition filter for the instrument summary status of a channel. Setting a bit in the positive transition filter causes a 0 to 1 transition in the corresponding condition register bit to write a 1 in the corresponding event register bit.

Name	Type	Values	Description
Channel	integer	1 - n	Channel suffix selecting the instrument summary instance.
PositiveTransition	integer	1 - 65535	Bit mask for the positive transition filter.

STATus:QUEStionable:INSTrument:ISUMmary1:PTRansition?

:STATus:QUEStionable:INSTrument:PTRansitionset / query

Sets or queries the positive transition filter. Setting a bit in the positive transition filter causes a 0 to 1 transition in the associated condition register bit to write a 1 to the corresponding event register bit.

Name	Type	Values	Description
arg0	integer	1 - 65535	Positive transition filter value.

integer - Returns the positive transition filter setting.

STATus:QUEStionable:INSTrument:ISUMmary1:PTRansition?

:STATus:OPERation:CONDition?query

Reads the condition register of the STATus:OPERation register. The register indicates which actions the instrument is currently executing.

integer - Returns the current contents of the STATus:OPERation CONDition register as a bit-coded value.

:STATus:OPERation[:EVENt]?query

Reads the event part of the STATus:OPERation register. The register reports which actions the instrument has executed since the last reading.

integer - Returns the STATus:OPERation event register value as a bit-coded integer.

:STATus:QUEStionable:CONDition?query

Returns the condition register of the STATus:QUEStionable register. The register contains information about different states which can occur.

integer - Returns the current contents of the STATus:QUEStionable condition register as a bit-coded value.

:STATus:QUEStionable[:EVENt]?query

Reads the STATus:QUEStionable register. The returned value is a decimal number that represents the bit pattern of the queried register.

integer - Decimal number representing the bit pattern of the queried register.

Products

Industries

Company

Blog

Rohde & Schwarz ROHDE-SCHWARZ-NGM202

Rohde & Schwarz ROHDE-SCHWARZ-NGM202

All commands

▶DIO12

▶SYSTem48

▶*13

▶DISPlay3

▶TRIGger13

▶INSTrument4

▶ALIMit2

▶VOLTage19

▶CURRent14

▶RESistance2

▶APPLy1

▶READ1

▶OUTPut12

▶SENSe4

▶FUSE6

▶POWer1

▶SOURce4

▶INTerfaces2

▶MEASure24

▶ARBitrary20

▶BATTery39

▶DATA4

▶HCOPy3

▶FLOG8

▶LOG8

▶STATus24